Airtac BSE Clamp Standard Cylinder BSE63X200S
The AirTAC Airtac BSE Clamp Standard Cylinder BSE63X200S is a genuine double-acting ISO 15552 cylinder with an integrated spring-applied, air-released ROD LOCK. If air is cut or an E-stop is hit, the collet clamps the Ø20mm rod and holds up to 2200 N in either direction — no drift. Ø63mm bore, 200mm stroke, PT3/8 cylinder ports, G1/8 lock-release port.
- BoreØ63 mm
- Stroke200 mm
- Static holding force2200 N
- Lock typeSpring-lock / air-release
- Cylinder portPT3/8
- Lock-release portG1/8
About the Airtac BSE Clamp Standard Cylinder BSE63X200S
The AirTAC BSE63X200S is a double-acting ISO 15552 profile cylinder with an integrated spring-applied, air-released rod lock. A collet clamps the Ø20 mm piston rod automatically, delivering a 2200 N bidirectional static holding force without consuming live air. Operating pressure is capped at 0.7 MPa, and the lock is managed via a dedicated G1/8 release port.
This 63 mm bore unit features an -S magnet for position sensing with CMSE reed or DMSE electronic sensors. The lock engages only after the rod fully stops and requires at least 0.5 s for pressure-balanced release before motion. The holding force comes strictly from the mechanical collet, not the adjustable air cushions at both ends.
Rod Lock — 2200 N Static Holding (Ø63mm)
A spring clamps the collet onto the rod, so the Airtac BSE Clamp Standard Cylinder BSE63X200S holds its position in both directions when air is lost, exhausted or an E-stop trips. Apply 0.15–0.7 MPa to the G1/8 release port to unlock. Engage the lock only after the rod has stopped (it is not a dynamic brake), and release only when the pressures on both sides of the piston are balanced. Allow at least 0.5 s for full release before moving.
Airtac BSE Clamp Standard Cylinder BSE63X200S Technical Specifications
| Model | Airtac BSE Clamp Standard Cylinder BSE63X200S |
|---|---|
| Series | BSE ISO 15552 rod-lock cylinder |
| Bore size | Ø63 mm |
| Stroke | 200 mm |
| Static holding force | 2200 N |
| Cylinder port | PT3/8 |
| Lock-release port | G1/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Unlocking pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC BSE datasheet. The lock uses the SE standard body; SE mounting accessories fit BSE except FTC. Port options: PT (standard) / G (BSPP); lock-release port is G1/8.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1402 N |
| 0.7 MPa (max) | 2182 N | — |
| Max drive (@0.7 MPa) | 223 kgf | |
Drive force is separate from the 2200 N static holding force of the lock. BSE operates up to 0.7 MPa. Size with a safety margin.
Model Code: Airtac BSE Clamp Standard Cylinder BSE63X200S
| B | Rod-lock cylinder prefix. |
|---|---|
| SE | ISO 15552 standard double-acting body. |
| 63 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Thread: PT (blank) / G. Mounting (BSE): Basic, LB, FA, FB, CA, CB, CR, TC (FTC is not available on BSE). Related: SE (no lock), BSED (double-rod rod lock). Sensors CMSE/DMSE fit magnetic BSE.
Where the Airtac BSE Clamp Standard Cylinder BSE63X200S Is Used
Vertical Pallet Lift
Holds a raised pallet mid-stroke with 2200 N of fail-safe force, preventing a crash if the main air supply drops suddenly during a vertical transfer.
Spindle Clamp
Locks a machining spindle actuator in position during a tool change, ensuring the 1559 N push force at 0.5 MPa does not drift while the workpiece is loaded.
Pallet Stopper
Acts as a rigid stop gate on a packaging conveyor. The collet lock engages instantly on E-stop to hold the accumulated queue without relying on live air.
Is the Airtac BSE Clamp Standard Cylinder BSE63X200S the Right Cylinder?
Verify your suspended load stays below the 2200 N holding force. If your load is lighter and you need less drive, step down to the 50 mm bore (push 982 N at 0.5 MPa, hold 1400 N). If you need more holding and drive force, step up to the 80 mm bore (push 2513 N at 0.5 MPa, hold 3600 N). The lock is a fail-safe hold, not a dynamic brake; engage it only after the rod stops and release it only when piston pressures are balanced. Replacement matches require 63 mm bore, 200 mm stroke, PT3/8 port, and your specific mounting (SE accessories fit except FTC).
Quick checklist
- ✓ Load to hold ≤ 2200 N?
- ✓ Fail-safe hold on air loss / E-stop needed
- ✓ Lock engaged only when stopped
- ✓ G1/8 release-air line available
- ✓ Magnet (-S) for CMSE/DMSE sensors?
Installation & Safety Notes
- check Engage the lock only after the rod has stopped — not as a dynamic brake.
- check Release only when both piston sides are pressure-balanced.
- check Allow ≥0.5 s for full release before commanding motion.
- check Feed the G1/8 release port with 0.15–0.7 MPa clean air.
- check Add safety-rated controls for man-rated / overhead loads.
- check Use SE mounting accessories (FTC excepted).
Airtac BSE Clamp Standard Cylinder BSE63X200S FAQ
On air loss, the spring-applied collet clamps the rod instantly, providing a 2200 N bidirectional static hold. The drive forces are 1559 N push and 1402 N pull at 0.5 MPa, 2182 N push at 0.7 MPa, and a maximum drive of 222 kgf.
Apply 0.15-0.7 MPa to the separate G1/8 release port only after balancing pressures on both sides of the piston. Wait at least 0.5 s for the collet to fully retract before commanding motion to avoid dragging the lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC BSE Cylinders
Request a Quote for Airtac BSE Clamp Standard Cylinder BSE63X200S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.