This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACE63X10S, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACP Compact Cylinder ACP63X10S
The AirTAC ACP Compact Cylinder ACP63X10S is a double acting DIN-standard tight/compact air cylinder with a Ø63mm bore and 10mm stroke, 1/8" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACE63X10S (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ63 mm
- Stroke10 mm
- Port size1/8"
- Acting typeDouble acting
- Rod threadM10×1.5
- StatusDiscontinued → ACE63X10S
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACP Compact Cylinder ACP63X10S
A double acting compact cylinder in the DIN-standard ACP series, the ACP63X10S pairs a 63 mm bore with a short 10 mm stroke and ships with the optional -S magnet already fitted, so CMSE or DMSE reed and solid-state switches can be mounted directly on the hard-anodized aluminium body. At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N; at 0.7 MPa those figures rise to 2182.1 N and 2041.3 N, with a theoretical peak of 317.9 kgf at 1.0 MPa. The short ISO 21287-class body saves roughly 50% of the mounting length of an ISO 15552 profile cylinder, which is why it slots into tight clamping fixtures and gantry stations where a full-length body will not fit.
The rod is 16 mm with a female M10x1.5 thread, the air port is 1/8", and a fixed TPU bumper at each end decelerates the piston. Note this model is discontinued: the current-production direct is the ACE63X10 in the same bore, stroke and force class - confirm the ISO 21287 mounting dimensions before swapping.
Airtac ACP Compact Cylinder ACP63X10S Technical Specifications
| Model | Airtac ACP Compact Cylinder ACP63X10S |
|---|---|
| Series | ACP DIN compact cylinder (discontinued) |
| Replacement | ACE63X10S |
| Bore size | Ø63 mm |
| Stroke | 10 mm |
| Acting type | Double acting |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 250 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACE63X10S (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1458 N |
| 0.7 MPa | 2182 N | 2041 N |
| Max (@1.0 MPa) | 318 kgf | |
The ACE63X10S produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac ACP Compact Cylinder ACP63X10S
| ACP | DIN compact cylinder (double-acting, discontinued). |
|---|---|
| 63 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACP Compact Cylinder ACP63X10S Is Used
Press-fit clamping of bearing housings
The 1558.6 N push at 0.5 MPa seats aluminium bearing housings into machined pockets on an assembly bench, with the 10 mm stroke covering the final clamp move only.
Carton hold-down on a packing line
Mounted above a conveyor, the short body holds cartons flat while flaps are taped, and the fitted -S magnet with a DMSE switch confirms the clamp is down before the tape head cycles.
Fixture ejection in a CNC cell
After machining, the cylinder kicks finished brackets off their locating pins; about 95 kg of usable working force at 0.5 MPa clears steel parts without marking the face.
Replacing the Airtac ACP Compact Cylinder ACP63X10S with the ACE63X10S
Size both ways before committing: a 50 mm bore gives 981.7 N push at 0.5 MPa if your load is lighter, while an 80 mm bore delivers 2513.3 N if you need more reserve. The 10 mm stroke suits short-throw clamping or ejection rather than long transfers, and 10 mm sits well inside the 250 mm maximum standard stroke for this bore, so no made-to-order stroke is involved. A plain cylinder of this type does not hold position when air is lost - add a rod lock or pilot check valve if the load must stay put. FA/FB flange, LB foot and CA/CB clevis mounts bolt to the standard face, and the fitted -S magnet accepts CMSE / DMSE switches. Order the ACE63X10 as the current replacement.
Replacement checklist
- ✓ Current-production ACE → ACE63X10S
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACP Compact Cylinder ACP63X10S FAQ
At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N; at 0.7 MPa, 2182.1 N push and 2041.3 N pull; theoretical maximum is 317.9 kgf at 1.0 MPa. It is a double acting compact cylinder with a 63 mm bore, 10 mm stroke, 16 mm rod with female M10x1.5 thread, 1/8" port, operating range 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, temperature -20 to +70 C, and a fixed TPU bumper at both ends.
AirTAC no longer produces the ACP family. The current direct is the ACE63X10 (swap the P for an E), an ISO 21287 compact cylinder in the same bore, stroke and force class with a matching short body and mounting family. Because the ACP was built to a DIN standard, confirm the ISO 21287 mounting dimensions against your fixture before swapping. The ACE also carries the optional -S magnet for CMSE / DMSE switches, matching what this model has fitted.
Request a Quote for the ACE63X10S
Send us the quantity and destination. We confirm price, stock and lead time on the ACE63X10S replacement — usually within 7-8 hours.