This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACED20X15S, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD20X15S
The AirTAC ACPD Double Rod Compact Cylinder ACPD20X15S is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø20mm bore and 15mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED20X15S (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ20 mm
- Stroke15 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod
- Rod threadM6×1.0
- StatusDiscontinued → ACED20X15S
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD20X15S
A double acting, double-rod compact cylinder built to the DIN-standard ACP layout, the ACPD20X15S pushes a 20 mm bore over a 15 mm stroke and delivers 117.8 N in BOTH directions at 0.5 MPa (164.9 N at 0.7 MPa), because the rod-side area works on each stroke. A 10 mm rod exits both covers, so the back-end rod can carry a sensor flag while the front rod does the work. This model carries the optional -S magnet, so CMSE or DMSE reed and solid-state switches can be clipped on for end-of-stroke signalling.
The short ISO 21287-class body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it slots into tight pick-and-place heads and small fixtures. Note the fixed TPU bumper at each end only softens the stroke ends; it never holds a load. This model is discontinued - the current-production direct is the ACED20X15 (swap the P for an E), so confirm ISO 21287 mounting dimensions before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD20X15S Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD20X15S |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED20X15S |
| Bore size | Ø20 mm |
| Stroke | 15 mm |
| Acting type | Double acting, double rod |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED20X15S (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø20mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 118 N |
| 0.7 MPa | 165 N |
| Max (@1.0 MPa) | 24 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD20X15S
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 20 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD20X15S Is Used
Small-part ejection from fixtures
The 15 mm stroke and 117.8 N per side are enough to kick machined brass fittings off a locating pin at the end of a drilling cycle, with the -S magnet confirming full retract each cycle.
Dual-side push in assembly heads
Because a rod exits both covers, one ACPD20X15S can press a bearing into a housing while the rear rod trips a position flag or drives a second small tool on the same stroke.
Gated indexing on compact conveyors
Mounted under a narrow conveyor guard where a full-length profile cylinder will not fit, the short body indexes 15 mm stops while CMSE or DMSE switches report end positions.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD20X15S with the ACED20X15S
At 117.8 N per side at 0.5 MPa, the 20 mm bore suits light clamping and part transfer; step down to the 16 mm bore (75.4 N) for smaller loads or up to the 25 mm bore (206.2 N) when you need roughly 75% more force. The through-rod resists rotation and gives a symmetric mount, and FA/FB flange or LB foot brackets bolt to the standard face. If the load must stay put when air is lost, add a rod lock or pilot check - this cylinder drifts. Order the ACED20X15 as your current-production replacement and verify the ISO 21287 footprint.
Replacement checklist
- ✓ Current-production ACE → ACED20X15S
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD20X15S FAQ
Yes - the double-rod design means both strokes use the rod-side area, so force is equal either way: 117.8 N at 0.5 MPa and 164.9 N at 0.7 MPa, with a maximum of 24.0 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the M5x0.8 port is fixed by the 20 mm bore.
Order the ACED20X15, the current-production ISO 21287 replacement (swap the P for an E). It matches the same 20 mm bore, 15 mm stroke and force class with a short compact body, but confirm the ISO 21287 mounting dimensions against your fixture before swapping, since the ACP was built to a DIN-standard layout. The -S magnet code carries over for CMSE / DMSE switch use.
Related AirTAC ACE Cylinders
Request a Quote for the ACED20X15S
Send us the quantity and destination. We confirm price, stock and lead time on the ACED20X15S replacement — usually within 7-8 hours.