This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACED25X10S, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD25X10S
The AirTAC ACPD Double Rod Compact Cylinder ACPD25X10S is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø25mm bore and 10mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED25X10S (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ25 mm
- Stroke10 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod
- Rod threadM6×1.0
- StatusDiscontinued → ACED25X10S
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD25X10S
A double acting compact cylinder with a rod leaving both covers, the ACPD25X10S pushes with equal force in each direction because both strokes work on the rod-side area: 206.2 N at 0.5 MPa and 288.6 N at 0.7 MPa. The 10 mm stroke suits short indexing moves inside tight fixtures, and the through-rod resists rotation while the rear rod can carry a sensor flag. This model carries the optional -S magnet, so CMSE or DMSE reed and solid-state switches mount directly on the body.
The hard-anodized aluminium body with an S45C hard-chrome rod runs on 0.15-1.0 MPa (22-145 psi) air filtered to 40 um, at 30-500 mm/s with fixed TPU bumpers at both ends. Its short ISO 21287-class body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which matters in crowded jig plates. Note this model is discontinued: the current-production direct is ACED25X10, so confirm ISO 21287 mounting dimensions before swapping.
Airtac ACPD Double Rod Compact Cylinder ACPD25X10S Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD25X10S |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED25X10S |
| Bore size | Ø25 mm |
| Stroke | 10 mm |
| Acting type | Double acting, double rod |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 150 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED25X10S (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD25X10S
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 25 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD25X10S Is Used
Jig plate part ejection
The 10 mm stroke and 206.2 N per side eject finished bushings from a drilling jig, and the short body fits under the drill head where a full-length cylinder cannot.
Flagged position feedback
With the -S magnet fitted, CMSE or DMSE switches read the piston position on a packaging machine's gate, while the rear rod carries a second flag for redundancy.
Symmetric push-pull slide
Equal 288.6 N at 0.7 MPa in both directions drives a small shuttle table on an electronics assembly line without any force imbalance between strokes.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD25X10S with the ACED25X10S
At 206.2 N per side at 0.5 MPa, bore 25 sits between the 16 mm bore (75.4 N) and the 32 mm bore (345.6 N), so step down for light pick-and-place or up for heavier clamping. The female M6x1.0 rod thread on both ends takes standard I/Y knuckles, and FA/FB flange or LB foot mounts bolt to the ISO 21287 face. Since a plain double-rod cylinder drifts when air is lost, add a rod lock or pilot check for held loads. Order ACED25X10 as the current replacement for this discontinued model.
Replacement checklist
- ✓ Current-production ACE → ACED25X10S
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD25X10S FAQ
Because a rod exits both covers, force is equal both ways: 206.2 N at 0.5 MPa and 288.6 N at 0.7 MPa, with a maximum of 42.0 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the port is M5x0.8.
The short ISO 21287-class body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with fixed TPU bumpers at both ends and FA/FB flange or LB foot options. This -S version carries the magnet, so CMSE and DMSE switches can be fitted; models ordered without -S have no magnet. The model is discontinued, and ACED25X10 is the current direct - confirm the ISO 21287 mounting dimensions before swapping.
Related AirTAC ACE Cylinders
Request a Quote for the ACED25X10S
Send us the quantity and destination. We confirm price, stock and lead time on the ACED25X10S replacement — usually within 7-8 hours.