This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACED25X60, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD25X60
The AirTAC ACPD Double Rod Compact Cylinder ACPD25X60 is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø25mm bore and 60mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED25X60 (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ25 mm
- Stroke60 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod
- Rod threadM6×1.0
- StatusDiscontinued → ACED25X60
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD25X60
A double acting compact cylinder with a rod leaving both covers, the ACPD25X60 pushes and pulls with identical force because each stroke works on the rod-side area: 206.2 N at 0.5 MPa and 288.6 N at 0.7 MPa in either direction. The through-rod resists rotation and light side load, and the rear rod can carry a sensor flag. A fixed TPU bumper sits at each end, and speed runs 30-500 mm/s.
The short ISO 21287-class body cuts roughly 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs and guarding. Note that this model is discontinued - the current-production direct is the ACED25X60, so confirm ISO 21287 mounting dimensions before swapping.
Airtac ACPD Double Rod Compact Cylinder ACPD25X60 Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD25X60 |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED25X60 |
| Bore size | Ø25 mm |
| Stroke | 60 mm |
| Acting type | Double acting, double rod |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 150 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED25X60 (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD25X60
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 25 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD25X60 Is Used
Symmetric jig clamping
The equal 206.2 N force in both directions lets one ACPD25X60 clamp and release a machined housing in a drilling fixture with the same grip either way.
Reciprocating slide drive
A through-rod driving a small conveyor gate from both ends keeps the 60 mm stroke square without an anti-rotation bracket, at speeds up to 500 mm/s.
Sensor flag carrier
With the optional -S magnet and a DMSE switch, the rear rod can carry a position flag on a packaging machine's reject chute actuator.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD25X60 with the ACED25X60
At 206.2 N per side, bore 25 suits clamping and transfer tasks in the 10-20 kg range; step down to bore 20 (117.8 N) for lighter fixtures or up to bore 32 (345.6 N) when more force is needed. The piston drifts if air is lost, so add a rod lock or pilot check for held loads. FA/FB flange and LB foot mountings bolt to the standard face, and the optional -S magnet enables CMSE / DMSE switches - this code has no magnet fitted. Order the ACED25X60 as the current replacement.
Replacement checklist
- ✓ Current-production ACE → ACED25X60
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD25X60 FAQ
Because a rod exits both covers, output is equal both ways: 206.2 N at 0.5 MPa and 288.6 N at 0.7 MPa, with a maximum of 42.0 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), and the 10 mm rod carries an M6x1.0 female thread. The M5x0.8 port depends only on the 25 mm bore.
The hard-anodized aluminium body follows the short ISO 21287-class format, saving about 50% of the mounting length of an ISO 15552 profile cylinder, with a fixed TPU bumper at each end. The ACPD family is discontinued; the ACED25X60 is the current direct in the same bore, stroke and force class - confirm the ISO 21287 mounting dimensions before swapping.
Request a Quote for the ACED25X60
Send us the quantity and destination. We confirm price, stock and lead time on the ACED25X60 replacement — usually within 7-8 hours.