This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACEJ16X110-75B, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPJ Adjustable Compact Cylinder ACPJ16X110-75B
The AirTAC ACPJ Adjustable Compact Cylinder ACPJ16X110-75B is a double acting, double rod, adjustable stroke DIN-standard tight/compact air cylinder with a Ø16mm bore and 110mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACEJ16X110-75B (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ16 mm
- Stroke110 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM4×0.7
- StatusDiscontinued → ACEJ16X110-75B
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPJ Adjustable Compact Cylinder ACPJ16X110-75B
The ACPJ16X110-75B is a double acting compact cylinder with an adjustable extend stroke: the -75 code gives a 75 mm stop-screw window, so the 110 mm stroke can be trimmed anywhere in a 35-110 mm range on site. The 16 mm bore delivers 100.5 N push and 75.4 N pull at 0.5 MPa (rising to 140.7 N at 0.7 MPa), which is enough to lift about 3 kg vertically with a 2:1 margin, and a practical rule is to plan for roughly 60 N of real work at 0.5 MPa rather than the full rating. The rod end is male thread (B code) and the air port is M5x0.8.
This model is discontinued. The current-production replacement is the ACEJ16X110, which keeps the same bore, stroke and force class in the ISO 21287 short-body format - a body that saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs and gantries. Note that the 110 mm stroke exceeds the 75 mm standard maximum for bore 16, so it is a made-to-order stroke. Confirm the ISO 21287 mounting dimensions before swapping, since the ACP is DIN-standard.
Airtac ACPJ Adjustable Compact Cylinder ACPJ16X110-75B Technical Specifications
| Model | Airtac ACPJ Adjustable Compact Cylinder ACPJ16X110-75B |
|---|---|
| Series | ACPJ DIN compact cylinder (discontinued) |
| Replacement | ACEJ16X110-75B |
| Bore size | Ø16 mm |
| Stroke | 110 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M4×0.7 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 75 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACEJ16X110-75B (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 75 N |
| 0.7 MPa | 106 N |
| Max (@1.0 MPa) | 15 kgf |
ACPJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac ACPJ Adjustable Compact Cylinder ACPJ16X110-75B
| ACPJ | DIN compact cylinder (adjustable-stroke, discontinued). |
|---|---|
| 16 | Bore size in mm. |
| ×110 | Stroke length in mm. |
| -75 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPJ Adjustable Compact Cylinder ACPJ16X110-75B Is Used
Ejection in a compact jig
Pushes a machined aluminium bracket off its locating pin on a drilling fixture, where the 35-110 mm adjustable range lets the setter dial in the eject travel without re-plumbing.
Small-carton push-off
Knocks a 200 g carton off a checkweigher belt into a reject chute; the 100.5 N push at 0.5 MPa clears the gap in under 0.2 s at 500 mm/s.
Clamp with end-position check
Clamps a plastic housing in an electronics assembly cell; order the -S magnet version with a CMSE switch to confirm the trimmed extend position before the press cycle starts.
Replacing the Airtac ACPJ Adjustable Compact Cylinder ACPJ16X110-75B with the ACEJ16X110-75B
Size both ways before committing: the 12 mm bore pushes 56.5 N at 0.5 MPa and the 20 mm bore pushes 157.1 N, so the 16 mm bore at 100.5 N sits between them - pick 20 mm if your part weight approaches the 60 N usable figure. The adjuster is a mechanical end stop for the extend stroke only, not a mid-stroke lock, so on air loss the piston still drifts; do not use it to hold a load. FA/FB flange and LB foot mountings bolt to the standard face, and if you need position sensing, order the -S code for the optional magnet - this model has no magnet, so no CMSE / DMSE switch can be mounted. For new projects, specify the ACEJ16X110 instead.
Replacement checklist
- ✓ Current-production ACE → ACEJ16X110-75B
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPJ Adjustable Compact Cylinder ACPJ16X110-75B FAQ
At 0.5 MPa it pushes 100.5 N and pulls 75.4 N; at 0.7 MPa it pushes 140.7 N and pulls 105.6 N; theoretical maximum is 20.5 kgf at 1.0 MPa. The -75 code is a 75 mm adjustment window: a stop screw shortens the 110 mm extend stroke by up to 75 mm, giving a usable 35-110 mm range. Operating pressure is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, with a fixed TPU bumper at both ends.
Bore 16 tops out at 75 mm as a standard stroke, so 110 mm is made to order. More importantly, the whole ACPJ family is discontinued: the drop-in successor is the ACEJ16X110, an ISO 21287 compact cylinder with the same bore, stroke and force class, male rod thread and M5x0.8 port. Confirm the ISO 21287 mounting dimensions against your fixture before swapping, because the ACP body is DIN-standard.
Related AirTAC ACE Cylinders
Request a Quote for the ACEJ16X110-75B
Send us the quantity and destination. We confirm price, stock and lead time on the ACEJ16X110-75B replacement — usually within 7-8 hours.