This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACEJ16X15-20, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPJ Adjustable Compact Cylinder ACPJ16X15-20
The AirTAC ACPJ Adjustable Compact Cylinder ACPJ16X15-20 is a double acting, double rod, adjustable stroke DIN-standard tight/compact air cylinder with a Ø16mm bore and 15mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACEJ16X15-20 (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ16 mm
- Stroke15 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM4×0.7
- StatusDiscontinued → ACEJ16X15-20
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPJ Adjustable Compact Cylinder ACPJ16X15-20
The ACPJ16X15-20 is a double acting compact cylinder with an adjustable extend stroke: a stop screw trims the 15 mm stroke within the ordered 20 mm window, so the usable range is 0-15 mm. At 0.5 MPa it pushes 100.5 N and pulls 75.4 N, rising to 140.7 N at 0.7 MPa. The hard-anodized aluminium body keeps the mounting length about 50% shorter than an ISO 15552 profile cylinder, which is why it slots into tight jigs and guarding where a full-length body will not fit.
A fixed TPU bumper sits at both ends, and the female M4x0.7 rod thread takes standard I/Y knuckles. Note that this model is discontinued: the current-production direct is the ACEJ16X15, so confirm ISO 21287 mounting dimensions before swapping.
Airtac ACPJ Adjustable Compact Cylinder ACPJ16X15-20 Technical Specifications
| Model | Airtac ACPJ Adjustable Compact Cylinder ACPJ16X15-20 |
|---|---|
| Series | ACPJ DIN compact cylinder (discontinued) |
| Replacement | ACEJ16X15-20 |
| Bore size | Ø16 mm |
| Stroke | 15 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M4×0.7 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 75 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACEJ16X15-20 (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 75 N |
| 0.7 MPa | 106 N |
| Max (@1.0 MPa) | 15 kgf |
ACPJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac ACPJ Adjustable Compact Cylinder ACPJ16X15-20
| ACPJ | DIN compact cylinder (adjustable-stroke, discontinued). |
|---|---|
| 16 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| -20 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPJ Adjustable Compact Cylinder ACPJ16X15-20 Is Used
Part-present check station
Short 0-15 mm trim makes it a go/no-go probe on assembly lines; order the -S version if CMSE / DMSE switch feedback is needed.
Compact indexing fixture
The short body, roughly half the length of an ISO 15552 profile cylinder, fits inside tight fixture plates and sliding gantries on electronics assembly cells.
Replacing the Airtac ACPJ Adjustable Compact Cylinder ACPJ16X15-20 with the ACEJ16X15-20
The stop screw only shortens the extend stroke - it is not a mid-stroke lock, so the piston still drifts if air is lost. Mounting uses FA/FB flanges or LB feet on the ISO 21287 face, and position sensing needs the optional -S magnet code (this unit has no magnet, so no CMSE / DMSE switch can be fitted). For new builds, order the ACEJ16X15 instead.
Replacement checklist
- ✓ Current-production ACE → ACEJ16X15-20
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPJ Adjustable Compact Cylinder ACPJ16X15-20 FAQ
At 0.5 MPa it pushes 100.5 N and pulls 75.4 N; at 0.7 MPa push is 140.7 N and pull 105.6 N. Theoretical maximum at 1.0 MPa is 20.5 kgf. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, port M5x0.8, rod 8 mm with female M4x0.7 thread.
The -20 code gives a 20 mm adjustment window: an external stop screw shortens the 15 mm extend stroke on site, giving a usable range of 0-15 mm. It is a mechanical end stop only, not a load-holding brake. This model is discontinued; the current-production replacement is the ACEJ16X15 in the same bore, stroke and force class - confirm ISO 21287 mounting dimensions before swapping.
Related AirTAC ACE Cylinders
Request a Quote for the ACEJ16X15-20
Send us the quantity and destination. We confirm price, stock and lead time on the ACEJ16X15-20 replacement — usually within 7-8 hours.