This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACEJ16X30-10SB, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPJ Adjustable Compact Cylinder ACPJ16X30-10SB
The AirTAC ACPJ Adjustable Compact Cylinder ACPJ16X30-10SB is a double acting, double rod, adjustable stroke DIN-standard tight/compact air cylinder with a Ø16mm bore and 30mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACEJ16X30-10SB (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ16 mm
- Stroke30 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM4×0.7
- StatusDiscontinued → ACEJ16X30-10SB
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPJ Adjustable Compact Cylinder ACPJ16X30-10SB
This discontinued AirTAC ACPJ16X30-10SB is a double acting compact cylinder with an adjustable extend stroke: a stop screw trims the 30 mm stroke by up to 10 mm, giving a usable 20-30 mm range. The 16 mm bore delivers 100.5 N push and 75.4 N pull at 0.5 MPa (rising to 140.7 N at 0.7 MPa), with a fixed TPU bumper at both ends and speeds of 30-500 mm/s. The short ISO 21287-class body saves roughly 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs and guarding where a full-length body will not fit.
The -S code means the magnet is fitted, so CMSE or DMSE reed and solid-state switches can be mounted for end-of-stroke signalling, and the B code gives a male rod thread on the 8 mm rod. For planning, treat about 60 N (0.6 x 100.5 N) as the realistic working force at 0.5 MPa, which corresponds to lifting roughly 3 kg vertically with a 2:1 margin. Note that the stop screw sets the extend position only - it is not a mid-stroke lock, so the piston still drifts if air is lost. This model is discontinued; the current-production replacement is the ACEJ16X30, so confirm ISO 21287 mounting dimensions before swapping.
Airtac ACPJ Adjustable Compact Cylinder ACPJ16X30-10SB Technical Specifications
| Model | Airtac ACPJ Adjustable Compact Cylinder ACPJ16X30-10SB |
|---|---|
| Series | ACPJ DIN compact cylinder (discontinued) |
| Replacement | ACEJ16X30-10SB |
| Bore size | Ø16 mm |
| Stroke | 30 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M4×0.7 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 75 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACEJ16X30-10SB (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 75 N |
| 0.7 MPa | 106 N |
| Max (@1.0 MPa) | 15 kgf |
ACPJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac ACPJ Adjustable Compact Cylinder ACPJ16X30-10SB
| ACPJ | DIN compact cylinder (adjustable-stroke, discontinued). |
|---|---|
| 16 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPJ Adjustable Compact Cylinder ACPJ16X30-10SB Is Used
Small jig clamping
The 100.5 N push at 0.5 MPa clamps aluminium brackets or plastic housings in drilling and small assembly jigs, with the 20-30 mm adjustable range matching varying part heights.
Position feedback on compact slides
With the fitted -S magnet, CMSE or DMSE switches signal extend and retract on short linear slides inside packaging machines where body length is critical.
Push-off in electronics fixtures
About 60 N of practical working force at 0.5 MPa ejects PCB carriers or connector trays from test fixtures, and the male rod thread accepts a knuckle for angled pushes.
Replacing the Airtac ACPJ Adjustable Compact Cylinder ACPJ16X30-10SB with the ACEJ16X30-10SB
Size the bore against your load: at 0.5 MPa the 16 mm bore pushes 100.5 N, the smaller 12 mm bore manages 56.5 N, and the larger 20 mm bore reaches 157.1 N. If you need to trim the extend stroke on site, the -10 window here covers 20-30 mm; order a wider window (up to 100 mm) if your setup may change. The male rod thread (B) suits I/Y knuckles, while FA flange or LB foot mounts bolt to the standard face. The optional -S magnet is fitted on this unit, enabling CMSE / DMSE switches. Since ACPJ is discontinued, specify the ACEJ16X30 as the drop-in successor and verify ISO 21287 dimensions before ordering.
Replacement checklist
- ✓ Current-production ACE → ACEJ16X30-10SB
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPJ Adjustable Compact Cylinder ACPJ16X30-10SB FAQ
At 0.5 MPa it pushes 100.5 N and pulls 75.4 N; at 0.7 MPa, 140.7 N push and 105.6 N pull; theoretical maximum is 20.5 kgf at 1.0 MPa. The -10 code gives a 10 mm adjustment window, so the extend stroke can be trimmed anywhere between 20 and 30 mm with the stop screw. Operating pressure is 0.15-1.0 MPa (22-145 psi) and speed is 30-500 mm/s.
No - the ACPJ family is discontinued. The current-production replacement is the ACEJ16X30 (swap the P for an E), which matches the same bore, stroke and force class. Because the ACPJ is DIN-standard while the ACE follows ISO 21287, confirm the mounting dimensions before swapping. The replacement keeps the short compact body, TPU bumpers and the optional magnet for CMSE / DMSE switches.
Related AirTAC ACE Cylinders
Request a Quote for the ACEJ16X30-10SB
Send us the quantity and destination. We confirm price, stock and lead time on the ACEJ16X30-10SB replacement — usually within 7-8 hours.