This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACEJ16X60-75, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPJ Adjustable Compact Cylinder ACPJ16X60-75
The AirTAC ACPJ Adjustable Compact Cylinder ACPJ16X60-75 is a double acting, double rod, adjustable stroke DIN-standard tight/compact air cylinder with a Ø16mm bore and 60mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACEJ16X60-75 (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ16 mm
- Stroke60 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM4×0.7
- StatusDiscontinued → ACEJ16X60-75
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPJ Adjustable Compact Cylinder ACPJ16X60-75
The ACPJ16X60-75 is a double acting compact cylinder with an adjustable extend stroke: a stop screw trims the 60 mm stroke on site within the ordered 75 mm window, so the usable range is 0-60 mm. The short ISO 21287-class body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which makes it easy to fit into shallow jigs, guarding frames and slide assemblies.
Built around a hard-anodized aluminium body with an S45C hard-chrome rod and a fixed TPU bumper at each end, it runs on 0.15-1.0 MPa (22-145 psi) filtered air at 30-500 mm/s. Note that this model is discontinued: the current-production replacement is the ACEJ16X60, and you should confirm the ISO 21287 mounting dimensions before swapping.
Airtac ACPJ Adjustable Compact Cylinder ACPJ16X60-75 Technical Specifications
| Model | Airtac ACPJ Adjustable Compact Cylinder ACPJ16X60-75 |
|---|---|
| Series | ACPJ DIN compact cylinder (discontinued) |
| Replacement | ACEJ16X60-75 |
| Bore size | Ø16 mm |
| Stroke | 60 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M4×0.7 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 75 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACEJ16X60-75 (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 75 N |
| 0.7 MPa | 106 N |
| Max (@1.0 MPa) | 15 kgf |
ACPJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac ACPJ Adjustable Compact Cylinder ACPJ16X60-75
| ACPJ | DIN compact cylinder (adjustable-stroke, discontinued). |
|---|---|
| 16 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -75 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPJ Adjustable Compact Cylinder ACPJ16X60-75 Is Used
Indexing stop on a rotary dial table
Used as a retractable stop pin on a 16-station indexing table, the 0-60 mm adjustable range sets the exact stop height, while the compact body fits inside the dial base plate.
Carton flap hold-down on a sealing head
Mounted above a carton sealer, the cylinder presses flaps flat with about 60 N of usable force at 0.5 MPa before the tape head passes, and the 60 mm stroke clears the box height.
Replacing the Airtac ACPJ Adjustable Compact Cylinder ACPJ16X60-75 with the ACEJ16X60-75
The stop screw only shortens the extend stroke - it is a mechanical end stop, not a mid-stroke lock, so the piston still drifts if air is lost. This unit has a female M4x0.7 rod thread and PT ports; FA/FB flange and LB foot mountings bolt to the standard face. No magnet is fitted, so position switches cannot be used - order the -S code for the optional magnet if you need CMSE / DMSE sensors. For new projects, specify the ACEJ16X60 instead.
Replacement checklist
- ✓ Current-production ACE → ACEJ16X60-75
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPJ Adjustable Compact Cylinder ACPJ16X60-75 FAQ
The -75 code is the 75 mm adjustment window: a stop screw shortens the 60 mm extend stroke on site, giving a usable range of 0-60 mm. It is double acting, runs on 0.15-1.0 MPa (22-145 psi) air at 30-500 mm/s, and the stop is an end stop only - it does not hold a load if air pressure is lost.
No - the ACPJ family is discontinued. The current-production direct is the ACEJ16X60 (swap the P for an E), which matches the same bore, stroke and force class; confirm the ISO 21287 mounting dimensions before swapping since the ACP is DIN-standard. As supplied, this unit has no magnet, so no sensor can be mounted; the optional -S magnet code enables CMSE / DMSE reed or solid-state switches. Mounting options are FA/FB flange and LB foot, and the fixed TPU bumpers decelerate the piston at both ends.
Related AirTAC ACE Cylinders
Request a Quote for the ACEJ16X60-75
Send us the quantity and destination. We confirm price, stock and lead time on the ACEJ16X60-75 replacement — usually within 7-8 hours.