The AirTAC BFC F.R.L Pneumatic Air Filter BFC2000A4 is a genuine A/B-line two-unit F.R.L. set with PT1/4" ports. It is the compact air-preparation line, regulating 0.15 - 0.9 MPa (20 - 130 psi) with a push-to-lock knob and oil-mist lubrication with a transparent sight dome. Flow is confirmed from the datasheet on request.
The BFC2000A4 is AirTAC's compact two-unit set: a filter-regulator plus a lubricator, sized for 1/4 in PT piping. The filter stage removes water and 40 um particulate from the compressed air, the regulator holds your set pressure with a push-to-lock self-locking knob that resists drift, and the lubricator meters oil mist downstream through a transparent sight dome so you can watch the drip rate. The A suffix is the automatic drain, which expels collected condensate without daily manual attention, and the supplied gauge reads in kgf/cm2 and psi.
This is a genuine AirTAC part from the compact A/B line, in the larger B-line body with high-strength plastic protective covers over the PC bowls. The family spans 1/8 to 1/2 in ports (1500 to 4000) in PT, G or NPT thread. It runs on compressed air at up to 1.0 MPa (145 psi) inlet, with a regulation range of 0.15-0.9 MPa (20-130 psi) and a working temperature of -5 to 70 C (non-freezing). Rated flow is not published as a single figure, so ask us and we will confirm flow and datasheet figures on request.
| Model | Airtac BFC F.R.L Pneumatic Air Filter BFC2000A4 |
|---|---|
| Type | Two-Unit (Filter-Regulator + Lubricator) |
| Line | B-line (compact A/B air preparation) |
| Port size | PT1/4" (PT thread) |
| Filter grade | 40 um standard, 5 um optional (W) |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) (low-pressure type to 0.4 MPa) |
| Fluid | Compressed air |
|---|---|
| Max. inlet pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 C (non-freezing) |
| Bowl material | PC (polycarbonate) |
| Lubrication | Oil-mist, transparent sight dome |
| Pressure drop | Low (catalogue-stated) |
Specifications follow the official AirTAC A/B-line air-preparation data. Drain type, filter grade, gauge and low-pressure options are set by the model-code suffix - see the description. Flow curves, weight and outline dimensions are not published in our data set — ask us and we confirm from the factory datasheet.
Choose the B-line 2000 body (1/4 in) when the larger compact body suits your line's flow demand; the A-line 2000 shares the port but uses the smaller body. The A suffix here is the automatic drain - pick it where daily draining is impractical; the default alternative is differential-pressure with manual drain. The filter element is the standard 40 um grade (a W suffix gives 5 um). The trailing 4 selects a gauge reading kgf/cm2 and psi (1 = MPa, 2 = psi, 3 = bar; N would delete the gauge). Thread is PT as standard; order G (BSPP) or T (NPT) variants if your piping needs them. Because flow is not a single published rating, ask us to confirm sizing against your demand before ordering.
Condition the shop-air feed to a CNC machine's pneumatic clamps and tool-changer cylinders: water and chips of particulate are filtered out, clamp pressure is held steady by the self-locking knob, and ways and seals get a light oil mist, with the auto drain handling condensate on its own.
Feed the stopper, diverter and pusher cylinders on a bottling line: clean, regulated, lubricated air keeps bottle-handling motions consistent through long shifts while the automatic drain copes with the moisture a compressed-air ring collects.
Supply pick-and-place grippers and small press cylinders in a robotic assembly cell, where the lubricator's visible drip dome lets a technician verify oil feed at a glance and the psi/kgf/cm2 gauge matches the plant's dial convention.
Rated flow is not published as a single figure for this set. AirTAC's datasheet gives flow characteristics instead, so send us your line pressure and air demand and we will confirm the right sizing from the datasheet on request.
The A selects the automatic drain: collected condensate is expelled without anyone opening the drain by hand. The default configuration uses a differential-pressure drain with manual operation, so choose the A version for units mounted where daily draining is impractical.