The AirTAC BFR Air Filter Regulator BFR2000A2T is a genuine A/B-line filter regulator with PT1/4" ports. It is the compact air-preparation line, regulating 0.15 - 0.9 MPa (20 - 130 psi) with a push-to-lock knob. Flow is confirmed from the datasheet on request.
The BFR2000A2T is a combined filter-regulator: one PC bowl and body remove water and particulate down to the standard 40 um grade and regulate downstream pressure between 0.15 and 0.9 MPa (20-130 psi). The A suffix selects the automatic drain, so accumulated condensate discharges from the bowl without an operator having to bleed it. Maximum inlet pressure is 1.0 MPa (145 psi), the operating temperature range is -5 to 70 C, non-freezing, and the medium is compressed air only. The push-to-lock self-locking knob keeps the set pressure from drifting, the included gauge carries a psi scale, and as a B-line unit the bowl sits behind a high-strength plastic protective cover.
This is a genuine AirTAC part from the compact A/B line in the 2000 (1/4 in) size. The family also comes in 1500 (1/8 in), 3000 (3/8 in) and 4000 (1/2 in), with NPT specified here and PT standard or G (BSPP) available to order. Flow and full datasheet figures are not published as a single rating; we confirm them on request.
| Model | Airtac BFR Air Filter Regulator BFR2000A2T |
|---|---|
| Type | Filter Regulator |
| Line | B-line (compact A/B air preparation) |
| Port size | PT1/4" (NPT thread) |
| Filter grade | 40 um standard, 5 um optional (W) |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) (low-pressure type to 0.4 MPa) |
| Fluid | Compressed air |
|---|---|
| Max. inlet pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 C (non-freezing) |
| Bowl material | PC (polycarbonate) |
| Pressure drop | Low (catalogue-stated) |
Specifications follow the official AirTAC A/B-line air-preparation data. Drain type, filter grade, gauge and low-pressure options are set by the model-code suffix - see the description. Flow curves, weight and outline dimensions are not published in our data set — ask us and we confirm from the factory datasheet.
The B-line 2000 size suits circuits with 1/4 in NPT ports where flow demand exceeds what the smaller A-line 1500 unit serves; step up to the 3000 or 4000 B-line bodies for heavier demand. Drain choice is the A-suffix automatic drain on this model, the default differential-pressure plus manual drain, or the M-suffix manual drain. Filtration is the standard 40 um element; specify the W suffix for the optional 5 um grade. This is the standard type with a psi-scale gauge included; the L suffix chooses the low-pressure type capped at 0.4 MPa and other scale digits select MPa, bar or kgf/cm2 gauges. PT is the family's standard thread, so this NPT version is an ordered option. Because airflow is not a single published rating, send us your flow requirement and we will confirm sizing from the datasheet before you order.
Mounted inside a machine's control cabinet supply run, the unit strips water and scale from shop air and holds a fixed regulated pressure for solenoid valves and pilot circuits.
Installed at a maintenance bench drop, the filter-regulator delivers clean, moisture-reduced air at the pressure the wrench was set up for, with the automatic drain coping with condensate between shifts.
Used on a bench test rig that cycles small pneumatic actuators, the unit provides filtered air and a locked, repeatable regulated pressure so test setups stay consistent run to run.
AirTAC does not publish flow for this filter-regulator as a single rated figure, and we will not estimate one. Tell us your required flow and we will confirm the correct size and the relevant datasheet figures on request before you order.
It selects the automatic drain. Condensate collected in the PC bowl discharges on its own instead of waiting for a manual bleed. The blank position gives the default differential-pressure plus manual drain, and M selects a purely manual drain.