This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACE80X125S, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACP Compact Cylinder ACP80X125S
The AirTAC ACP Compact Cylinder ACP80X125S is a double acting DIN-standard tight/compact air cylinder with a Ø80mm bore and 125mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACE80X125S (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ80 mm
- Stroke125 mm
- Port size1/4"
- Acting typeDouble acting
- Rod threadM12×1.75
- StatusDiscontinued → ACE80X125S
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACP Compact Cylinder ACP80X125S
Double acting on both strokes, the ACP80X125S is AirTAC's DIN-standard compact cylinder with an 80 mm bore and 125 mm stroke, a hard-anodized aluminium body and an S45C hard-chrome 20 mm rod. At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N, rising to 3518.6 N / 3298.7 N at 0.7 MPa, with a theoretical ceiling of 512.6 kgf at 1.0 MPa. The short ISO 21287-class body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight presses, gates and fixtures. The -S code on this model means the magnet is fitted, so CMSE or DMSE reed and solid-state switches can be clipped on for end-of-stroke sensing.
A fixed TPU bumper at each end only softens the stroke ends; it never holds a load, so add a rod lock or pilot check valve where the rod must stay put if air is lost. This model is discontinued: the current-production direct is ACE80X125, same bore, stroke and force class - confirm the ISO 21287 mounting dimensions before swapping.
Airtac ACP Compact Cylinder ACP80X125S Technical Specifications
| Model | Airtac ACP Compact Cylinder ACP80X125S |
|---|---|
| Series | ACP DIN compact cylinder (discontinued) |
| Replacement | ACE80X125S |
| Bore size | Ø80 mm |
| Stroke | 125 mm |
| Acting type | Double acting |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACE80X125S (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2356 N |
| 0.7 MPa | 3519 N | 3299 N |
| Max (@1.0 MPa) | 513 kgf | |
The ACE80X125S produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac ACP Compact Cylinder ACP80X125S
| ACP | DIN compact cylinder (double-acting, discontinued). |
|---|---|
| 80 | Bore size in mm. |
| ×125 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACP Compact Cylinder ACP80X125S Is Used
Pneumatic press for aluminium crimping
The 2513.3 N push at 0.5 MPa crimps terminals and light aluminium fittings; the 125 mm stroke clears loading by hand and the short body fits under a low press head.
Clamping fixture on a machining centre
Roughly 1508 N of usable clamp force at 0.5 MPa holds steel parts in a milling fixture; the compact body mounts where a full-length profile cylinder would not fit, with LB foot or FA flange plates.
Replacing the Airtac ACP Compact Cylinder ACP80X125S with the ACE80X125S
At 80 mm bore this sits near the top of the range: 2513.3 N push at 0.5 MPa versus 981.7 N for a 50 mm bore, while the 100 mm bore steps up to 3927.0 N. If your load needs under about 1500 N of real work, the 63 mm bore (1558.6 N push) may be enough. Stroke 125 mm is well inside the 300 mm maximum standard stroke for this bore, so it is a catalogue item, not made to order. FA/FB flange, LB foot, CA/CB clevis, CR, SDB pivot and FTC brackets bolt to the same face, and the fitted -S magnet pairs with CMSE / DMSE switches. Since ACP is discontinued, order ACE80X125 and verify the ISO 21287 mounting dimensions.
Replacement checklist
- ✓ Current-production ACE → ACE80X125S
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACP Compact Cylinder ACP80X125S FAQ
Push is 2513.3 N and pull 2356.2 N at 0.5 MPa; at 0.7 MPa push is 3518.6 N and pull 3298.7 N; theoretical maximum is 512.6 kgf at 1.0 MPa. It is a double-acting compact cylinder, 80 mm bore, 125 mm stroke, 20 mm rod with female M12x1.25 thread class per datasheet, 1/4" PT ports, operating pressure 0.15-1.0 MPa (22-145 psi), proof 1.5 MPa (215 psi), speed 30-500 mm/s, temperature -20 to +70 C, air filtered to 40 um, fixed TPU bumpers at both ends. Confirm exact thread and dimensions from the datasheet.
Order ACE80X125, the ISO 21287 successor: swap the P for an E and you get the same 80 mm bore, 125 mm stroke and force class in a current-production short-body cylinder. The ACP is DIN-standard, so before swapping check the ISO 21287 mounting dimensions and the FA/FB, LB, CA/CB, CR, SDB or FTC bracket fit. If you also need end-of-stroke sensing, the -S magnet option on the ACE carries the same CMSE / DMSE switches.
Related AirTAC ACE Cylinders
Request a Quote for the ACE80X125S
Send us the quantity and destination. We confirm price, stock and lead time on the ACE80X125S replacement — usually within 7-8 hours.