This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACE80X150B, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACP Compact Cylinder ACP80X150B
The AirTAC ACP Compact Cylinder ACP80X150B is a double acting DIN-standard tight/compact air cylinder with a Ø80mm bore and 150mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACE80X150B (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ80 mm
- Stroke150 mm
- Port size1/4"
- Acting typeDouble acting
- Rod threadM12×1.75
- StatusDiscontinued → ACE80X150B
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACP Compact Cylinder ACP80X150B
A double acting compact cylinder with a 20 mm rod, the ACP80X150B pushes 2513.3 N and pulls 2356.2 N at 0.5 MPa, rising to 3518.6 N on extension at 0.7 MPa. Its short ISO 21287-class body saves roughly 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into presses, gantries and guarding where a full-length body cannot. The hard-anodized aluminium body carries a S45C hard-chrome rod, with a fixed TPU bumper at each end, and the male rod thread (B code) suits knuckle and tooling attachments directly.
Note that this unit holds nothing when air is lost: the piston drifts, so add a rod lock or pilot check valve for a suspended load. The model is discontinued; the current-production direct is ACE80X150, same bore, stroke and force class, so confirm the ISO 21287 mounting dimensions before swapping.
Airtac ACP Compact Cylinder ACP80X150B Technical Specifications
| Model | Airtac ACP Compact Cylinder ACP80X150B |
|---|---|
| Series | ACP DIN compact cylinder (discontinued) |
| Replacement | ACE80X150B |
| Bore size | Ø80 mm |
| Stroke | 150 mm |
| Acting type | Double acting |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACE80X150B (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2356 N |
| 0.7 MPa | 3519 N | 3299 N |
| Max (@1.0 MPa) | 513 kgf | |
The ACE80X150B produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac ACP Compact Cylinder ACP80X150B
| ACP | DIN compact cylinder (double-acting, discontinued). |
|---|---|
| 80 | Bore size in mm. |
| ×150 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACP Compact Cylinder ACP80X150B Is Used
Baling and compaction ram
With 2513.3 N of push at 0.5 MPa and 3518.6 N at 0.7 MPa, the 80 mm bore drives a small baling or scrap-compaction platen over the 150 mm stroke inside a tight frame.
Clamping fixture on a machining line
The short body fits between fixture plates where an ISO 15552 profile cylinder will not, and the male rod thread takes a knuckle for swing clamps on aluminium die-cast housings.
Replacing the Airtac ACP Compact Cylinder ACP80X150B with the ACE80X150B
At 80 mm bore this is near the top of the range: it delivers 2513.3 N at 0.5 MPa versus 1558.6 N for a 63 mm bore, while a 100 mm bore reaches 3927.0 N if you need more reserve. Stroke 150 mm sits well inside the 300 mm standard limit for this bore, so no made-to-order build is needed. This version has the male rod thread and no magnet - order the -S code if you want CMSE / DMSE switch detection. FA/FB flange, LB foot and CA/CB clevis mountings bolt to the standard face. Since ACP is discontinued, specify ACE80X150 as the replacement and verify the ISO 21287 hole pattern first.
Replacement checklist
- ✓ Current-production ACE → ACE80X150B
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACP Compact Cylinder ACP80X150B FAQ
Push is 2513.3 N and pull is 2356.2 N at 0.5 MPa; at 0.7 MPa push rises to 3518.6 N and pull to 3298.7 N. Theoretical maximum is 512.6 kgf at 1.0 MPa. It runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), temperature -20 to +70 C, speed 30-500 mm/s, with a 1/4" port and 20 mm rod.
It is a compact short-body cylinder with a hard-anodized aluminium body, S45C hard-chrome rod, male rod thread and a fixed TPU bumper at both ends - the bumper only decelerates at the ends and never holds a load, so use a rod lock or pilot check valve for that. Position sensing needs the optional -S magnet ordered with CMSE / DMSE switches. The model is discontinued; ACE80X150 is the current direct, so confirm the ISO 21287 mounting dimensions before converting.
Related AirTAC ACE Cylinders
Request a Quote for the ACE80X150B
Send us the quantity and destination. We confirm price, stock and lead time on the ACE80X150B replacement — usually within 7-8 hours.