This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACEJ16X60-10B, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPJ Adjustable Compact Cylinder ACPJ16X60-10B
The AirTAC ACPJ Adjustable Compact Cylinder ACPJ16X60-10B is a double acting, double rod, adjustable stroke DIN-standard tight/compact air cylinder with a Ø16mm bore and 60mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACEJ16X60-10B (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ16 mm
- Stroke60 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM4×0.7
- StatusDiscontinued → ACEJ16X60-10B
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPJ Adjustable Compact Cylinder ACPJ16X60-10B
The ACPJ16X60-10B is a double acting, adjustable-stroke compact cylinder with a 16 mm bore and 60 mm stroke. An external stop screw trims the extend stroke by up to 10 mm, giving a usable range of 50-60 mm on site. At 0.5 MPa it pushes 100.5 N and pulls 75.4 N, rising to 140.7 N at 0.7 MPa. Its short ISO 21287-class body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs and guarding. Note: this model is discontinued; the current-production replacement is the ACEJ16X60.
The 8 mm S45C hard-chrome rod ends in a MALE thread (the B code), and air ports are M5x0.8. A fixed TPU bumper at both ends decelerates the piston; the stop screw sets stroke length but is not a mid-stroke lock, so the rod still drifts if air is lost. For planning, treat roughly 60 N (about 6 kg lifted vertically with a 2:1 margin) as the practical working force at 0.5 MPa. Operating range is 0.15-1.0 MPa (22-145 psi) at 30-500 mm/s. No magnet is fitted on this version; the optional -S code adds one for CMSE / DMSE switches. Confirm ISO 21287 mounting dimensions before swapping to the ACEJ16X60.
Airtac ACPJ Adjustable Compact Cylinder ACPJ16X60-10B Technical Specifications
| Model | Airtac ACPJ Adjustable Compact Cylinder ACPJ16X60-10B |
|---|---|
| Series | ACPJ DIN compact cylinder (discontinued) |
| Replacement | ACEJ16X60-10B |
| Bore size | Ø16 mm |
| Stroke | 60 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M4×0.7 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 75 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACEJ16X60-10B (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 75 N |
| 0.7 MPa | 106 N |
| Max (@1.0 MPa) | 15 kgf |
ACPJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac ACPJ Adjustable Compact Cylinder ACPJ16X60-10B
| ACPJ | DIN compact cylinder (adjustable-stroke, discontinued). |
|---|---|
| 16 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPJ Adjustable Compact Cylinder ACPJ16X60-10B Is Used
Small-parts ejection from fixtures
The 100.5 N push at 0.5 MPa is enough to kick machined aluminum brackets off a locating nest, and the 10 mm trim lets the operator fine-tune ejection travel between 50 and 60 mm.
Light clamping on electronics assembly benches
Holding a PCB carrier or connector housing during screwdriving needs only a few tens of newtons; the compact short body fits under low fixture plates where a full-length cylinder will not.
Indexed slide on a labeler or filler
A 60 mm advance positions small containers or cartons on a packaging line; with the optional -S magnet, CMSE / DMSE switches report end positions without external limit switches.
Replacing the Airtac ACPJ Adjustable Compact Cylinder ACPJ16X60-10B with the ACEJ16X60-10B
Size both ways: if 100.5 N at 0.5 MPa is marginal for your load, step up to the 20 mm bore (157.1 N push); if the load is light, the 12 mm bore (56.5 N push) saves more space. The 60 mm stroke is within the 75 mm standard limit for bore 16, so no made-to-order stroke is needed. Choose FA/FB flange or LB foot mounting to suit the fixture, and order the -S variant if position sensing via CMSE / DMSE switches is planned. For new designs, specify the current ACEJ16X60 instead of this discontinued model.
Replacement checklist
- ✓ Current-production ACE → ACEJ16X60-10B
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPJ Adjustable Compact Cylinder ACPJ16X60-10B FAQ
At 0.5 MPa it pushes 100.5 N and pulls 75.4 N; at 0.7 MPa, 140.7 N push and 105.6 N pull. The theoretical maximum is 20.5 kgf at 1.0 MPa. The stop screw shortens the extend stroke by up to 10 mm (usable 50-60 mm), and the male-threaded 8 mm rod connects via standard I/Y knuckles. This model is discontinued - the ACEJ16X60 is the current drop-in, so confirm ISO 21287 mounting dimensions before ordering.
An external stop screw on the head limits extension anywhere within the ordered 10 mm window, so the rod stops between 50 and 60 mm of travel. It is a mechanical end stop only - on air loss the piston still drifts, so do not rely on it to hold a load. Position sensing requires the optional -S magnet code; this version has no magnet, so CMSE / DMSE switches cannot be mounted unless you order the -S variant or the ACEJ16X60 equivalent.
Related AirTAC ACE Cylinders
Request a Quote for the ACEJ16X60-10B
Send us the quantity and destination. We confirm price, stock and lead time on the ACEJ16X60-10B replacement — usually within 7-8 hours.