This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ASE80X10S, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ASP Single Acting Guided Compact Cylinder ASP80X10S
The AirTAC ASP Single Acting Guided Compact Cylinder ASP80X10S is a single acting, push (spring return) DIN-standard tight/compact air cylinder with a Ø80mm bore and 10mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ASE80X10S (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ80 mm
- Stroke10 mm
- Port size1/4"
- Acting typeSingle acting, push (spring return)
- Rod threadM12×1.75
- StatusDiscontinued → ASE80X10S
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ASP Single Acting Guided Compact Cylinder ASP80X10S
A single acting push cylinder with spring return, the ASP80X10S uses one air line to extend its 20 mm rod while an internal spring pulls it back to the retracted home position. This 80 mm bore unit delivers 2316.2 N of push at 0.5 MPa (3321.5 N at 0.7 MPa), both figures already net of the spring, and it needs just 0.2 MPa to overcome the spring and start moving. The S in the code means the optional -S magnet is fitted, so CMSE or DMSE reed and solid-state switches can be clipped on for end-of-stroke signalling.
The short ISO 21287-class body cuts mounting length by roughly half compared with an ISO 15552 profile cylinder, which is why it slots into cramped press fixtures and clamping nests. Note this model is discontinued: the current-production replacement is the ASE80X10, so confirm ISO 21287 mounting dimensions before swapping.
Airtac ASP Single Acting Guided Compact Cylinder ASP80X10S Technical Specifications
| Model | Airtac ASP Single Acting Guided Compact Cylinder ASP80X10S |
|---|---|
| Series | ASP DIN compact cylinder (discontinued) |
| Replacement | ASE80X10S |
| Bore size | Ø80 mm |
| Stroke | 10 mm |
| Acting type | Single acting, push (spring return) |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.2 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 25 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ASE80X10S (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Push force (spring return) |
|---|---|
| 0.5 MPa | 2316.2 N |
| 0.7 MPa | 3321.5 N |
Single-acting push: air extends the rod; the return spring retracts it. Forces already net the spring; minimum working pressure is 0.2 MPa.
Model Code: Airtac ASP Single Acting Guided Compact Cylinder ASP80X10S
| ASP | DIN compact cylinder (single-acting push, spring-return, discontinued). |
|---|---|
| 80 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ASP Single Acting Guided Compact Cylinder ASP80X10S Is Used
Short-stroke press fit
The 2316.2 N push at 0.5 MPa suits pressing bearings or bushings into aluminium housings on a 10 mm working stroke, with the spring clearing the nest between cycles.
Pallet clamp actuation
One air line clamps a machined pallet in a CNC fixture; air loss lets the spring retract the clamp so the part is never trapped in a stalled cylinder.
Presence check with signalling
With the fitted -S magnet and a DMSE switch, the 80 mm bore confirms a heavy casting is seated in a machining jig before the cycle starts.
Replacing the Airtac ASP Single Acting Guided Compact Cylinder ASP80X10S with the ASE80X10S
Size between bores: a 63 mm bore gives 1420.5 N at 0.5 MPa, while this 80 mm unit reaches 2316.2 N; if you need more, the 100 mm bore pushes 3640.7 N at the same pressure. Because the spring drives the rod home on air loss, the cylinder cannot hold an arbitrary mid-stroke position - plan your fixture around the normally retracted state. The 10 mm stroke sits well inside the standard range for this bore, and the female M12x1.75 rod thread plus 1/4" PT port keeps plumbing simple. Order CMSE or DMSE switches to use the fitted -S magnet. For new projects, specify the ASE80X10 instead, as the ASP line is discontinued.
Replacement checklist
- ✓ Current-production ACE → ASE80X10S
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ASP Single Acting Guided Compact Cylinder ASP80X10S FAQ
Push force is 2316.2 N at 0.5 MPa and 3321.5 N at 0.7 MPa, both already net of the return spring. Operating range is 0.2-1.0 MPa (28-145 psi) with 1.5 MPa (215 psi) proof pressure, minimum 0.2 MPa to beat the spring, speed 50-500 mm/s, and temperature -20 to +70 C on air filtered to 40 um.
The ISO 21287-class short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits tight jigs and gantries. A fixed TPU bumper pads each end of travel only; on air loss the spring simply retracts the rod to its home position and does not lock or hold a mid-stroke load. This model is discontinued - the direct successor is the ASE80X10, so confirm ISO 21287 mounting dimensions before swapping.
Request a Quote for the ASE80X10S
Send us the quantity and destination. We confirm price, stock and lead time on the ASE80X10S replacement — usually within 7-8 hours.