This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACED32X10B, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD32X10B
The AirTAC ACPD Double Rod Compact Cylinder ACPD32X10B is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø32mm bore and 10mm stroke, 1/8" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED32X10B (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ32 mm
- Stroke10 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM8×1.25
- StatusDiscontinued → ACED32X10B
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD32X10B
A double acting compact cylinder with a rod exiting BOTH covers, the ACPD32X10B delivers 345.6 N in each direction at 0.5 MPa (483.8 N at 0.7 MPa) because both strokes work on the rod-side area of the 32 mm bore. The 10 mm stroke suits short-reach clamping and positioning where a full-length body would never fit: the ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder. This model is discontinued; the current-production direct is ACED32X10, so confirm ISO 21287 mounting dimensions before swapping from the DIN-standard ACP footprint.
The through-rod resists rotation and side load and gives a symmetric mount, and the back-end rod can carry a sensor flag on other variants. A fixed TPU bumper sits at both ends, and speed runs 30-500 mm/s over 0.15-1.0 MPa (22-145 psi) air filtered to 40 um. Note this unit has no magnet: order the -S code if you need CMSE / DMSE switch sensing.
Airtac ACPD Double Rod Compact Cylinder ACPD32X10B Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD32X10B |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED32X10B |
| Bore size | Ø32 mm |
| Stroke | 10 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED32X10B (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD32X10B
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 32 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD32X10B Is Used
Press-fit pin insertion
The 10 mm stroke and 345.6 N per side at 0.5 MPa suit seating dowel pins or bushings in small aluminium housings on an electronics assembly bench.
Symmetric fixture clamping
With a rod on both covers, one cylinder can clamp a workpiece from opposite sides in a machining fixture, keeping the mount balanced and rotation-resistant.
Short-reach part kickers
The compact body fits beside narrow conveyor frames to deflect small cartons or blisters at a transfer point, running 30-500 mm/s.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD32X10B with the ACED32X10B
At 345.6 N per side at 0.5 MPa, the 32 mm bore sits between the 25 mm (206.2 N) and 40 mm (571.8 N) options - step down for lighter clamps, up when a fixture needs nearly double the force. The male rod thread (B code) takes standard rod accessories directly. A plain double-rod cylinder does not hold position when air is lost, so add a rod lock or pilot check for a suspended load. FA/FB flange or LB foot mounting bolts to the ISO 21287 face. Choose ACED32X10 as the current replacement and verify the mounting dimensions.
Replacement checklist
- ✓ Current-production ACE → ACED32X10B
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD32X10B FAQ
Because a rod exits both covers, force is EQUAL in both directions: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa, both sides working on the rod-side area of the 32 mm bore. Maximum force at 1.0 MPa is 70.5 kgf. Operating range is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure.
Only with the optional -S magnet code. This ACPD32X10B (no S in the code) has no magnet, so no switch can be mounted. Ordering the -S variant enables CMSE or DMSE reed / solid-state switches along the body. Also note the model is discontinued - the ACED32X10 is the current direct, so confirm ISO 21287 mounting dimensions before ordering.
Related AirTAC ACE Cylinders
Request a Quote for the ACED32X10B
Send us the quantity and destination. We confirm price, stock and lead time on the ACED32X10B replacement — usually within 7-8 hours.