This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACED32X110, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD32X110
The AirTAC ACPD Double Rod Compact Cylinder ACPD32X110 is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø32mm bore and 110mm stroke, 1/8" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED32X110 (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ32 mm
- Stroke110 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM8×1.25
- StatusDiscontinued → ACED32X110
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD32X110
The ACPD32X110 is a double acting compact cylinder with a rod leaving both covers, so the 345.6 N output at 0.5 MPa (483.8 N at 0.7 MPa) is identical on the extend and retract strokes because both sides work on the rod-side area. The through-rod resists rotation and light side load, gives a symmetric mounting point at each end, and the rear rod can carry a sensor flag. A fixed TPU bumper sits at each cover, and travel speed runs 30-500 mm/s.
Its ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it slots into tight jigs, guards and gantries. The hard-anodized aluminium body carries a 12 mm S45C hard-chrome rod with a female M8x1.25 thread, and the 1/8" PT ports depend only on the 32 mm bore. This model is discontinued: the current-production direct is ACED32X110, so confirm ISO 21287 mounting dimensions before swapping. Note that a plain through-rod cylinder drifts when air is lost - use a rod lock or pilot check if a load must stay held.
Airtac ACPD Double Rod Compact Cylinder ACPD32X110 Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD32X110 |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED32X110 |
| Bore size | Ø32 mm |
| Stroke | 110 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED32X110 (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD32X110
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 32 | Bore size in mm. |
| ×110 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD32X110 Is Used
Two-sided press fixture
The equal 345.6 N force in both directions lets one cylinder clamp a bracket on the forward stroke and eject it on the return, with the 110 mm stroke clearing a deep die pocket.
Reciprocating guide carriage
A rod at each cover anchors the carriage symmetrically on a small assembly gantry, where the through-rod resists rotation and the short body fits the 110 mm envelope.
Rear-rod flag position check
On a bottling-line gate, the back rod carries a flag plate read by a photo sensor; order the -S magnet version instead if CMSE or DMSE switches are preferred.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD32X110 with the ACED32X110
If your fixture needs more, step up to the 40 mm bore at 571.8 N; if less, the 25 mm bore delivers 206.2 N. The 110 mm stroke sits inside the 200 mm standard range for this bore. Mounting is FA/FB flange or LB foot, and because no S code is ordered here there is no magnet, so CMSE or DMSE switches cannot be fitted - choose ACPD32X110S if position sensing is needed. For new designs, order the ACED32X110 instead, as this ACPD is discontinued.
Replacement checklist
- ✓ Current-production ACE → ACED32X110
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD32X110 FAQ
Yes. Because a rod exits both covers, both strokes use the rod-side area, so force is equal both ways: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa, with a maximum of 70.5 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the 1/8" port depends only on the 32 mm bore.
Order ACED32X110, the current-production ISO 21287 successor: swap the P for an E and you get the same 32 mm bore, 110 mm stroke and force class in a matching short body. Confirm the ISO 21287 mounting dimensions against your fixture before swapping, since the ACPD was built to the older DIN-standard layout. FA/FB flange and LB foot options carry over, and the fixed TPU bumpers at both covers do the same end-of-travel job.
Related AirTAC ACE Cylinders
Request a Quote for the ACED32X110
Send us the quantity and destination. We confirm price, stock and lead time on the ACED32X110 replacement — usually within 7-8 hours.