This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACED32X110SB, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD32X110SB
The AirTAC ACPD Double Rod Compact Cylinder ACPD32X110SB is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø32mm bore and 110mm stroke, 1/8" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED32X110SB (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ32 mm
- Stroke110 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM8×1.25
- StatusDiscontinued → ACED32X110SB
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD32X110SB
Double acting with a rod leaving both covers, the ACPD32X110SB pushes and pulls with the same 345.6 N at 0.5 MPa (483.8 N at 0.7 MPa), because each stroke works on the rod-side area. This 32 mm bore, 110 mm stroke version carries the -S magnet code and a male rod thread (B). The through-rod resists rotation and light side load, gives a symmetric mounting face, and the rear rod can carry a sensor flag. A fixed TPU bumper sits at each end, and speed runs 30-500 mm/s at 0.15-1.0 MPa (22-145 psi).
The short ISO 21287-class body cuts roughly 50% of the mounting length compared with an ISO 15552 profile cylinder, so it slots into tight jigs and gantries. Note that this model is discontinued: the current-production direct is the ACED32X110, so confirm ISO 21287 mounting dimensions before swapping.
Airtac ACPD Double Rod Compact Cylinder ACPD32X110SB Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD32X110SB |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED32X110SB |
| Bore size | Ø32 mm |
| Stroke | 110 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED32X110SB (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD32X110SB
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 32 | Bore size in mm. |
| ×110 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD32X110SB Is Used
Reciprocating transfer slide
The equal 345.6 N push and pull at 0.5 MPa moves a small pallet fixture back and forth over the 110 mm stroke at up to 500 mm/s, with the rear rod carrying a position flag.
Symmetric press or clinch station
A compact electronics assembly cell uses the through-rod to seat connectors from both sides, where identical force in each direction keeps crimp depth consistent.
Gantry pick point with switch feedback
Mounted under a pick-and-place gantry with CMSE or DMSE switches on the -S magnet, the cylinder confirms end positions on a 110 mm vertical transfer of parts up to about 18 kg.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD32X110SB with the ACED32X110SB
Size both ways: a 25 mm bore double-rod unit gives 206.2 N at 0.5 MPa, while a 40 mm bore reaches 571.8 N, so step up if your fixture needs more than the 345.6 N this bore delivers. The through-rod suits symmetric tooling and the rear rod can drive a switch flag; order CMSE or DMSE switches to suit the -S magnet this model carries. FA/FB flange and LB foot mounts bolt to the standard face. Like any plain double-rod cylinder it will drift when air is lost, so add a rod lock or pilot check for a held load. Order the ACED32X110 as the current replacement.
Replacement checklist
- ✓ Current-production ACE → ACED32X110SB
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD32X110SB FAQ
Because a rod exits both covers, force is equal in both directions: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa, with a maximum of 70.5 kgf at 1.0 MPa.
Order the ACED32X110, the ISO 21287 successor made by swapping the P for an E. It matches the same 32 mm bore, 110 mm stroke and force class with a similar short aluminium body, but confirm the ISO 21287 mounting dimensions against your fixture before swapping, since the ACP was built to a DIN-standard footprint.
Related AirTAC ACE Cylinders
Request a Quote for the ACED32X110SB
Send us the quantity and destination. We confirm price, stock and lead time on the ACED32X110SB replacement — usually within 7-8 hours.