This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACED32X200, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD32X200
The AirTAC ACPD Double Rod Compact Cylinder ACPD32X200 is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø32mm bore and 200mm stroke, 1/8" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED32X200 (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ32 mm
- Stroke200 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM8×1.25
- StatusDiscontinued → ACED32X200
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD32X200
A double acting compact cylinder with a rod leaving both covers, the ACPD32X200 pushes and pulls with identical force because each stroke works on the rod-side area: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa, equal in both directions. The 32 mm bore drives a 12 mm through-rod over a 200 mm stroke, which is the maximum standard stroke for this bore, at speeds of 30-500 mm/s.
The hard-anodized aluminium body with an S45C hard-chrome rod keeps the mounting length roughly 50% shorter than an ISO 15552 profile cylinder, so it slots into tight gantries and guarding where a full-length body will not fit. The through-rod resists rotation and side load and lets the rear rod carry a sensor flag. Note this model is discontinued: the current direct is the ACED32X200, so confirm ISO 21287 mounting dimensions before swapping.
Airtac ACPD Double Rod Compact Cylinder ACPD32X200 Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD32X200 |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED32X200 |
| Bore size | Ø32 mm |
| Stroke | 200 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED32X200 (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD32X200
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 32 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD32X200 Is Used
Reciprocating transfer arm
The symmetric through-rod gives equal 345.6 N push and pull at 0.5 MPa, ideal for a shuttle that must index a 10 kg fixture tray back and forth over 200 mm on a small assembly cell.
Dual-end position flagging
With the optional -S magnet and CMSE switches, both rod ends can trip end-of-stroke sensors on a packaging machine, while the rear rod carries a second flag for a PLC interlock.
Compact jig clamping
A body about 50% shorter than an ISO 15552 profile cylinder fits inside a welding fixture guard, delivering 483.8 N at 0.7 MPa to seat a bracket against a locating pin.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD32X200 with the ACED32X200
Size by force first: at 0.5 MPa the 32 mm bore gives 345.6 N both ways, while the 25 mm bore offers 206.2 N and the 40 mm bore 571.8 N, so step up if your part mass or friction load demands more. The 200 mm stroke is the largest standard stroke for this bore, so nothing is made to order here. Remember the piston drifts when air is lost - add a rod lock or pilot check if the load must stay put. This unit has no magnet fitted; order the -S code if you need CMSE or DMSE switches. For new designs, specify the ACED32X200 instead, as the ACPD line is discontinued.
Replacement checklist
- ✓ Current-production ACE → ACED32X200
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD32X200 FAQ
Yes - the double-rod design means both strokes use the rod-side area, so output is equal both ways: 345.6 N at 0.5 MPa, 483.8 N at 0.7 MPa, with a maximum of 70.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the 1/8" port suits the 32 mm bore.
The ACPD is no longer in production; the current-production direct is the ACED32X200 (swap the P for an E), which matches the same 32 mm bore, 200 mm stroke and force class in the ISO 21287 family - confirm the mounting dimensions before swapping, since the ACP is DIN-standard. For sensing on this unit, the magnet is the optional -S code; without it no CMSE or DMSE switch can be mounted.
Related AirTAC ACE Cylinders
Request a Quote for the ACED32X200
Send us the quantity and destination. We confirm price, stock and lead time on the ACED32X200 replacement — usually within 7-8 hours.