Airtac B01-MAC Series Special Purpose Cylinder B01-MAC20X175SCM
The AirTAC B01-MAC Series Special Purpose Cylinder B01-MAC20X175SCM is a genuine double acting + cushion standard round-body mini air cylinder with a Ø0mm bore and 175mm stroke, PT/G air ports and a stainless-steel barrel with a hard-chrome-plated rod for reliable, mildly corrosion-resistant service. A variable air cushion at both ends lets you tune end-of-stroke deceleration on site.
- BoreØ0 mm
- Stroke175 mm
- Port sizePT/G
- Acting typeDouble acting + cushion
- Rod thread
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac B01-MAC Series Special Purpose Cylinder B01-MAC20X175SCM
A 175 mm reach, a pivoting CM round-end cover and 157 N of push at 0.5 MPa make the MAC20X175SCM a natural for long-throw link arms. Double acting with variable air cushions at each end, it runs 30-800 mm/s on a 0.15-1.0 MPa (22-145 psi) supply and proofs to 1.5 MPa (215 psi).
The round barrel is stainless steel, riveted to aluminium-alloy covers in a rolling-packed joint that will not work loose, and the carbon-steel rod wears 20 um of hard chrome against corrosion.
Airtac B01-MAC Series Special Purpose Cylinder B01-MAC20X175SCM Technical Specifications
| Model | Airtac B01-MAC Series Special Purpose Cylinder B01-MAC20X175SCM |
|---|---|
| Series | MAC mini cylinder |
| Bore size | Ø0 mm |
| Stroke | 175 mm |
| Acting type | Double acting + cushion |
| Port size | PT/G |
| Rod thread |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MA-series datasheet. Barrel: stainless-steel tube (round-body, riveted rolling-packed construction); piston rod: carbon steel with 20µm hard-chrome plating; covers: aluminium alloy. Thread options: PT (blank) / G / NPT. Every MA-series cylinder ships with a built-in magnet for CMSG / DMSG / EMSG position sensors.
Theoretical Output Force (Ø0mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 0 N | 0 N |
| 0.7 MPa | 0 N | 0 N |
| Max (@1.0 MPa) | 0 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac B01-MAC Series Special Purpose Cylinder B01-MAC20X175SCM
| MAC | Standard round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 0 | Bore size in mm. |
| ×175 | Stroke length in mm. |
| -S | Built-in magnet for CMSG / DMSG / EMSG sensors (standard on MA series). |
| CA / U / CM | Back-cover type: CA pivot, U flat-end, CM round-end. |
MA-family variants: MA / MAC (double acting ±cushion), MSA / MTA (single acting push / pull), MAD / MACD (double rod ±cushion), MAJ / MACJ (double rod, adjustable stroke ±cushion), MAR (cushioned with integrated F/U mount). Mounting accessories: FA flange, LB foot, SDB pivot; plus I and Y knuckles. Thread PT (blank) / G / NPT.
Where the Airtac B01-MAC Series Special Purpose Cylinder B01-MAC20X175SCM Is Used
Stretching station on a bag-making machine
Pulling film edges taut ahead of the seal bar - the 175 mm stroke spreads the web and the adjustable cushion eases the arms home at the end of every cycle.
Roller-gate latch in a picking bay
Swinging a gate latch open at the end of a gravity roller run - the round-end pivot matches the latch lever directly and a DMSG switch reports the locked status back to the WMS.
Connector pusher in a cable test rig
Seating connector modules into a test jig - about 94 N of working force seats the contacts gently, and the chrome rod shrugs off the flux fumes in the enclosure.
Is the Airtac B01-MAC Series Special Purpose Cylinder B01-MAC20X175SCM the Right Cylinder?
If 157 N at 0.5 MPa overshoots the job, a bore 16 barrel gives 100.5 N; if the arm gets heavier, a bore 25 cylinder offers 245.3 N. Note the MAC has no internal lock - centred valve, drifting piston - so hang a pilot check valve or rod lock on any load that must stay raised. The CM round end carries a pivot pin in line with the thrust; FA flange, LB foot or SDB pivot brackets handle fixed points, and the standard magnet pairs with CMSG, DMSG and EMSG switches. Air enters through 1/8" ports on this bore, and external guiding matters at 175 mm: keep side load off the 8 mm chrome rod to protect the bearing and cushion seals.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) is standard for sensors
- ✓ Back cover (CA/U/CM) & mount (FA/LB/SDB)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check On first run, back off the cushion screws and release gradually.
- check Installation by qualified personnel per AirTAC docs.
Airtac B01-MAC Series Special Purpose Cylinder B01-MAC20X175SCM FAQ
Push 157 N and pull 131.9 N at 0.5 MPa; push 219.8 N and pull 184.7 N at 0.7 MPa; theoretical maximum 32 kgf at 1.0 MPa. Supply pressure range is 0.15-1.0 MPa (22-145 psi) with 1.5 MPa (215 psi) proof pressure.
No - every MAC20X175SCM includes the magnet as standard, so CMSG, DMSG or EMSG switches snap onto the stainless barrel for end-of-stroke or mid-stroke signalling with no special-order piston required.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac B01-MAC Series Special Purpose Cylinder B01-MAC20X175SCM
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.