This model is discontinued
AirTAC has phased out the MAL series. You can still order this code here: we ship the direct replacement MBL40X600S-CA, with the same bore, stroke, output force, port and mounting, so it fits the same application. The MBL replacement upgrades to a riveted rolling-packed body and the current CMSG / DMSG / EMSG sensor switches (the MAL used CS1-M / DS1-M).
The AirTAC MAL40X600S-CA (Discontinued) -> MBL40X600S-CA is a double-acting aluminum-barrel mini round cylinder with a Ø40mm bore and 600mm stroke, G1/4 air ports and a fixed rubber bumper. This model is discontinued — the direct replacement is the MBL40X600S-CA, which matches its bore, stroke, force and mounting.
The AirTAC MAL40X600S-CA is a discontinued double-acting aluminum mini round cylinder with a 40mm bore and 600mm stroke. It delivers 628N push and 528N pull at 0.5MPa via a G1/4 port. The direct replacement is the MBL40X600S-CA, matching the bore, stroke, force, port, and CA pivot mounting.
This legacy unit features a built-in magnet (-S) for position detection and a CA pivot clevis back cover designed for arcing loads. The original MAL body uses threaded front and back covers, whereas the modern MBL replacement features a riveted rolling-packed body. Additionally, the -S magnet on this MAL works with older CS1-M / DS1-M switches, while the MBL successor requires the current CMSG / DMSG / EMSG sensor family.
| Model | AirTAC MAL40X600S-CA (Discontinued) -> MBL40X600S-CA |
|---|---|
| Series | MAL aluminum-barrel mini round cylinder (discontinued) |
| Replacement | MBL40X600S-CA |
| Bore size | Ø40 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MAL datasheet (now discontinued). The MBL40X600S-CA carries the same ratings. Confirm against the product label before installation. Thread options: PT / G / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | — |
| Max (@1.0 MPa) | 128 kgf | |
The MBL40X600S-CA produces the same force from the same bore. Actual usable force is lower than theoretical; size with a margin.
| MAL | Aluminum-barrel mini round cylinder, double acting (discontinued). |
|---|---|
| 40 | Bore size in mm (20/25/32/40). |
| ×600 | Stroke length in mm. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBL uses CMSG/DMSG/EMSG). |
| CA / U / CM | Back cover: CA pivot, U flat-end or CM round-end. |
Replacement mapping: MAL → MBL, MSAL → MSBL, MTAL → MTBL, MALD → MBLD, MALJ → MBLJ.
Drives a 600mm pivoting transfer arm on a packaging machine, utilizing the CA clevis to safely swing components without binding the rod.
Pushes heavy pallets sideways at a sorting junction, using the 628N push force at 0.5MPa to overcome sliding friction.
Actuates a 600mm lift gate on a testing fixture, relying on the G1/4 port for rapid fill and exhaust to maintain cycle speeds.
To replace the MAL40X600S-CA, order the MBL40X600S-CA. Confirm the 40mm bore, 600mm stroke, G1/4 port, PT thread, and CA pivot back cover. Because the 600mm stroke exceeds the 500mm standard maximum, this is a made-to-order non-standard stroke. If you need to adjust sizing, stepping down to the 32mm bore yields 402N push at 0.5MPa, while stepping up to a 50mm profile cylinder provides significantly higher force.
At 600mm of travel, the 16mm rod is highly susceptible to bending forces; the CA pivot mounting is essential to absorb side-load arcing, though an external guide rail is strongly recommended for rigid loads. Note that the fixed rubber bumper softens end-of-stroke impact but does not lock the rod if air pressure drops. If your application requires adjustable end-cushioning for that heavy 128kgf max load, specify the MBLC variant on the current line instead of the standard MBL.
Upgrade checklist
Yes, the MAL40X600S-CA is discontinued. The direct replacement is the MBL40X600S-CA, offering the same 40mm bore, 600mm stroke, CA pivot mounting, and G1/4 port. Note that the MBL uses a riveted body instead of threaded covers, and the magnet sensor family changes from CS1-M / DS1-M to CMSG / DMSG / EMSG.
At 0.5MPa it provides 628N push and 528N pull; at 0.7MPa it provides 880N push, with a theoretical maximum of 128kgf at 1.0MPa. It uses a fixed rubber bumper for end-of-stroke cushioning, not an adjustable air cushion. If adjustable cushioning is required for this 600mm stroke, the current-line MBLC variant should be used.
Genuine AirTAC parts produced by AirTAC factory.
The MBL40X600S-CA replaces this model 1:1.
MBL replacements are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Tell us the quantity and destination — we quote the direct MBL40X600S-CA replacement with price, stock and lead time, usually within 7-8 hours.