This model is discontinued
AirTAC has phased out the MALJ series. You can still order this code here: we ship the direct replacement MBLJ25X100-10, with the same bore, stroke, output force, port and mounting, so it fits the same application. The MBLJ replacement upgrades to a riveted rolling-packed body and CMSG / DMSG / EMSG sensors (the MAL used CS1-M / DS1-M).
Airtac MALJ25 Adjustable Mini Air Cylinder MALJ25X100-10
The AirTAC MALJ25 Adjustable Mini Air Cylinder MALJ25X100-10 is a double-acting aluminum mini cylinder with a rear adjustable-stroke stopper: you can trim up to 10 mm, giving a usable end-position window from 90 to 100 mm. This model is discontinued — the direct replacement is the MBLJ25X100-10.
- BoreØ25 mm
- Stroke100 mm
- Adjust window90–100 mm
- Port sizeG1/8
- Rod threadM10×1.25
- StatusDiscontinued → MBLJ25X100-10
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MALJ25 Adjustable Mini Air Cylinder MALJ25X100-10
The AirTAC MALJ25X100-10 is a discontinued double-acting, double-rod mini cylinder with a 10 mm rear adjustable stroke stopper. It provides a usable stroke window of 90-100 mm. The direct replacement is the MBLJ25X100-10, which matches the bore, stroke, force, and mounting.
This SKU lacks the -S magnet code, so it cannot accept a position sensor. The rear adjuster is a travel stop, not a lock; it cannot hold a load without live air pressure. The original MALJ features threaded covers and a fixed rubber bumper, whereas the MBLJ upgrade uses a riveted rolling-packed body. Both designs rely on a heterogeneous grease-retaining seal and a 20 um hard chrome carbon-steel rod.
Airtac MALJ25 Adjustable Mini Air Cylinder MALJ25X100-10 Technical Specifications
| Model | Airtac MALJ25 Adjustable Mini Air Cylinder MALJ25X100-10 |
|---|---|
| Series | MALJ adjustable-stroke mini cylinder (discontinued) |
| Replacement | MBLJ25X100-10 |
| Bore size | Ø25 mm |
| Stroke | 100 mm |
| Adjustable window | 90 – 100 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 300 mm |
The rear adjuster is a travel stop, not a lock — it sets the end position but does not hold the load without live air. No back-cover code and no SDB on adjustable-stroke. The MBLJ25X100-10 carries the same ratings.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
MALJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod MAL push of the same bore. The MBLJ25X100-10 matches these values.
Model Code: Airtac MALJ25 Adjustable Mini Air Cylinder MALJ25X100-10
| MALJ | Adjustable-stroke aluminum mini cylinder, double acting (discontinued). |
|---|---|
| 25 | Bore size in mm (20/25/32/40). |
| ×100 | Nominal stroke length in mm. |
| -10 | Adjustable amount: trim the end to a 90–100 mm window. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBLJ uses CMSG/DMSG/EMSG). |
Replacement: MALJ → MBLJ. No back-cover (CA/U/CM) and no SDB. Mounting: FA / LB.
Where the Airtac MALJ25 Adjustable Mini Air Cylinder MALJ25X100-10 Is Used
PCB Router Z-Axis
Dial in the 90-100 mm descent on a PCB depaneling router to cut exact depths without repositioning the cylinder block.
Pneumatic Press Stop
Set a precise 90 mm bottom position on a small assembly press, letting the fixed rubber bumper absorb the 50 kgf peak impact.
Replacing the Airtac MALJ25 Adjustable Mini Air Cylinder MALJ25X100-10 with MBLJ25X100-10
To replace the MALJ25X100-10, specify the MBLJ25X100-10. Confirm the 25 mm bore, 100 mm stroke, 10 mm adjust code, G1/8 port, PT thread, and FA or LB mounting. This unit has no -S magnet, so no sensor is used; if you later need a switch, the MBLJ takes CMSG/DMSG/EMSG sensors instead of the older CS1-M/DS1-M. Remember the adjuster sets end position but does not hold load.
Upgrade checklist
- ✓ Order the MBLJ25X100-10 (same bore/stroke/adjust)
- ✓ Same 90–100 mm adjustable window
- ✓ Adjuster is a stop, not a lock
- ✓ No back cover / SDB — plan an FA/LB mount
- ✓ Sensor: swap CS1-M/DS1-M → CMSG/DMSG/EMSG
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.1 – 1.0 MPa operating pressure.
- check The rear adjuster sets the end position — it is not a load lock.
- check No back-cover / SDB on adjustable-stroke — use FA / LB.
- check Front/rear covers are threaded — not for field disassembly.
- check For new builds, specify the MBLJ25X100-10 instead of this discontinued model.
Airtac MALJ25 Adjustable Mini Air Cylinder MALJ25X100-10 FAQ
Yes, the MALJ25X100-10 is discontinued. The direct replacement is the MBLJ25X100-10, which keeps the same 25 mm bore, 100 mm stroke, 10 mm adjust code, and G1/8 port. The MBLJ upgrades the body to a riveted rolling-packed design from the original threaded covers.
The 10 mm adjuster trims the rear position, giving a usable stroke window of 90-100 mm. This adjuster is a travel stop, not a lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
Direct Upgrade
The MBLJ25X100-10 replaces this model 1:1.
Fast Dispatch
MBLJ replacements are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Recommended AirTAC MBLJ Replacements
Request a Quote (Airtac MALJ25 Adjustable Mini Air Cylinder MALJ25X100-10 → MBLJ25X100-10)
Tell us the quantity and destination — we quote the direct MBLJ25X100-10 replacement with price, stock and lead time, usually within 7-8 hours.