This model is discontinued
AirTAC has phased out the MALJ series. You can still order this code here: we ship the direct replacement MBLJ25X95-10, with the same bore, stroke, output force, port and mounting, so it fits the same application. The MBLJ replacement upgrades to a riveted rolling-packed body and CMSG / DMSG / EMSG sensors (the MAL used CS1-M / DS1-M).
Airtac MALJ25 Adjustable Mini Air Cylinder MALJ25X95-10
The AirTAC MALJ25 Adjustable Mini Air Cylinder MALJ25X95-10 is a double-acting aluminum mini cylinder with a rear adjustable-stroke stopper: you can trim up to 10 mm, giving a usable end-position window from 85 to 95 mm. This model is discontinued — the direct replacement is the MBLJ25X95-10.
- BoreØ25 mm
- Stroke95 mm
- Adjust window85–95 mm
- Port sizeG1/8
- Rod threadM10×1.25
- StatusDiscontinued → MBLJ25X95-10
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MALJ25 Adjustable Mini Air Cylinder MALJ25X95-10
The AirTAC MALJ25X95-10 is a discontinued double-acting double-rod mini cylinder with a 10 mm rear stroke adjustment. This gives a usable end-position window of 85-95 mm. The direct replacement is the MBLJ25X95-10, matching the bore, stroke, adjuster and G1/8 port.
This SKU has no magnet, so it cannot take a position sensor. The rear adjuster is a travel stop, not a lock; it sets the end position but will not hold a load without live air. Upgrading to the MBLJ moves from threaded covers to a riveted rolling-packed body. Impact is absorbed by a fixed rubber bumper, not an adjustable air cushion.
Airtac MALJ25 Adjustable Mini Air Cylinder MALJ25X95-10 Technical Specifications
| Model | Airtac MALJ25 Adjustable Mini Air Cylinder MALJ25X95-10 |
|---|---|
| Series | MALJ adjustable-stroke mini cylinder (discontinued) |
| Replacement | MBLJ25X95-10 |
| Bore size | Ø25 mm |
| Stroke | 95 mm |
| Adjustable window | 85 – 95 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 300 mm |
The rear adjuster is a travel stop, not a lock — it sets the end position but does not hold the load without live air. No back-cover code and no SDB on adjustable-stroke. The MBLJ25X95-10 carries the same ratings.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
MALJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod MAL push of the same bore. The MBLJ25X95-10 matches these values.
Model Code: Airtac MALJ25 Adjustable Mini Air Cylinder MALJ25X95-10
| MALJ | Adjustable-stroke aluminum mini cylinder, double acting (discontinued). |
|---|---|
| 25 | Bore size in mm (20/25/32/40). |
| ×95 | Nominal stroke length in mm. |
| -10 | Adjustable amount: trim the end to a 85–95 mm window. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBLJ uses CMSG/DMSG/EMSG). |
Replacement: MALJ → MBLJ. No back-cover (CA/U/CM) and no SDB. Mounting: FA / LB.
Where the Airtac MALJ25 Adjustable Mini Air Cylinder MALJ25X95-10 Is Used
PCB Router Z-Axis
Dial the 85-95 mm window to set the exact cutting depth on a PCB depaneling router without machining new hard stops.
Bench Press Pin Insertion
Use the 10 mm rear stop to precisely limit the downward travel when pressing delicate connector pins into aluminum housings.
Replacing the Airtac MALJ25 Adjustable Mini Air Cylinder MALJ25X95-10 with MBLJ25X95-10
To replace this MALJ25X95-10 with the MBLJ25X95-10, confirm the 25 mm bore, 95 mm stroke, 10 mm adjust code, PT G1/8 port and FA/LB mounting (no back cover or SDB). Since this SKU lacks the -S magnet, it uses no sensor; if you need detection on the new MBLJ, you must add an -S model and use CMSG/DMSG/EMSG switches instead of the older CS1-M/DS1-M.
Remember the adjuster is a stop, not a lock; use an external lock for held loads.
Upgrade checklist
- ✓ Order the MBLJ25X95-10 (same bore/stroke/adjust)
- ✓ Same 85–95 mm adjustable window
- ✓ Adjuster is a stop, not a lock
- ✓ No back cover / SDB — plan an FA/LB mount
- ✓ Sensor: swap CS1-M/DS1-M → CMSG/DMSG/EMSG
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.1 – 1.0 MPa operating pressure.
- check The rear adjuster sets the end position — it is not a load lock.
- check No back-cover / SDB on adjustable-stroke — use FA / LB.
- check Front/rear covers are threaded — not for field disassembly.
- check For new builds, specify the MBLJ25X95-10 instead of this discontinued model.
Airtac MALJ25 Adjustable Mini Air Cylinder MALJ25X95-10 FAQ
Yes, the MALJ25X95-10 is discontinued. The direct replacement is the MBLJ25X95-10, which matches the 25 mm bore, 95 mm stroke, 10 mm adjuster, G1/8 port and force. The MBLJ upgrades the construction to a riveted rolling-packed body.
The -10 code is a rear travel stop that lets you trim the end position, creating a usable 85-95 mm window. It does not hold the load without air pressure.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
Direct Upgrade
The MBLJ25X95-10 replaces this model 1:1.
Fast Dispatch
MBLJ replacements are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Recommended AirTAC MBLJ Replacements
Request a Quote (Airtac MALJ25 Adjustable Mini Air Cylinder MALJ25X95-10 → MBLJ25X95-10)
Tell us the quantity and destination — we quote the direct MBLJ25X95-10 replacement with price, stock and lead time, usually within 7-8 hours.