This model is discontinued
AirTAC has phased out the MALJ series. You can still order this code here: we ship the direct replacement MBLJ40X15-10-S, with the same bore, stroke, output force, port and mounting, so it fits the same application. The MBLJ replacement upgrades to a riveted rolling-packed body and CMSG / DMSG / EMSG sensors (the MAL used CS1-M / DS1-M).
Airtac MALJ40 Adjustable Mini Cylinder MALJ40X15-10-S
The AirTAC MALJ40 Adjustable Mini Cylinder MALJ40X15-10-S is a double-acting aluminum mini cylinder with a rear adjustable-stroke stopper: you can trim up to 10 mm, giving a usable end-position window from 5 to 15 mm. This model is discontinued — the direct replacement is the MBLJ40X15-10-S.
- BoreØ40 mm
- Stroke15 mm
- Adjust window5–15 mm
- Port sizeG1/4
- Rod threadM12×1.25
- StatusDiscontinued → MBLJ40X15-10-S
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MALJ40 Adjustable Mini Cylinder MALJ40X15-10-S
The AirTAC MALJ40X15-10-S is a discontinued adjustable-stroke mini cylinder. As a direct replacement, use the MBLJ40X15-10-S, which matches the 40mm bore, 15mm stroke, G1/4 port and force ratings. This SKU provides a usable extension window of 5-15mm by trimming up to 10mm at the rear screw.
This double-acting double-rod cylinder uses a fixed rubber bumper, not an adjustable air cushion. The rear adjuster is a travel stop, not a lock; it sets the end position but will not hold a load without live air. For your upgrade, the MALJ uses threaded covers and a CS1-M/DS1-M magnet, while the MBLJ replacement features a riveted rolling-packed body and uses CMSG/DMSG/EMSG switches.
Airtac MALJ40 Adjustable Mini Cylinder MALJ40X15-10-S Technical Specifications
| Model | Airtac MALJ40 Adjustable Mini Cylinder MALJ40X15-10-S |
|---|---|
| Series | MALJ adjustable-stroke mini cylinder (discontinued) |
| Replacement | MBLJ40X15-10-S |
| Bore size | Ø40 mm |
| Stroke | 15 mm |
| Adjustable window | 5 – 15 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | G1/4 |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.1 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed rubber bumper |
| Max standard stroke | Up to 500 mm |
The rear adjuster is a travel stop, not a lock — it sets the end position but does not hold the load without live air. No back-cover code and no SDB on adjustable-stroke. The MBLJ40X15-10-S carries the same ratings.
Theoretical Output Force (Ø40mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 528 N | 528 N |
| 0.7 MPa | 739 N | — |
| Max (@1.0 MPa) | 108 kgf | |
MALJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod MAL push of the same bore. The MBLJ40X15-10-S matches these values.
Model Code: Airtac MALJ40 Adjustable Mini Cylinder MALJ40X15-10-S
| MALJ | Adjustable-stroke aluminum mini cylinder, double acting (discontinued). |
|---|---|
| 40 | Bore size in mm (20/25/32/40). |
| ×15 | Nominal stroke length in mm. |
| -10 | Adjustable amount: trim the end to a 5–15 mm window. |
| S | Optional magnet for a CS1-M / DS1-M sensor (MBLJ uses CMSG/DMSG/EMSG). |
Replacement: MALJ → MBLJ. No back-cover (CA/U/CM) and no SDB. Mounting: FA / LB.
Where the Airtac MALJ40 Adjustable Mini Cylinder MALJ40X15-10-S Is Used
Sheet Metal Spot Welder
Fine-tune the electrode reach on a robotic spot welder, setting the exact 5-15mm end position to maintain consistent weld nuggets on steel panels.
Replacing the Airtac MALJ40 Adjustable Mini Cylinder MALJ40X15-10-S with MBLJ40X15-10-S
To replace this MALJ40X15-10-S with the MBLJ40X15-10-S, confirm the 40mm bore, 15mm stroke, 10mm adjust code, PT G1/4 port and M12x1.25 rod-end thread. Mounting is FA or LB only; there is no back-cover or SDB option. Because this is a -S magnet SKU, you must change your sensors: the old CS1-M/DS1-M switches will not fit the MBLJ, which requires CMSG/DMSG/EMSG switches. Remember the rear adjuster is a stop, not a lock; use an external lock for held loads.
Upgrade checklist
- ✓ Order the MBLJ40X15-10-S (same bore/stroke/adjust)
- ✓ Same 5–15 mm adjustable window
- ✓ Adjuster is a stop, not a lock
- ✓ No back cover / SDB — plan an FA/LB mount
- ✓ Sensor: swap CS1-M/DS1-M → CMSG/DMSG/EMSG
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.1 – 1.0 MPa operating pressure.
- check The rear adjuster sets the end position — it is not a load lock.
- check No back-cover / SDB on adjustable-stroke — use FA / LB.
- check Front/rear covers are threaded — not for field disassembly.
- check For new builds, specify the MBLJ40X15-10-S instead of this discontinued model.
Airtac MALJ40 Adjustable Mini Cylinder MALJ40X15-10-S FAQ
Yes, the MALJ40X15-10-S is discontinued. The direct replacement is the MBLJ40X15-10-S, matching the 40mm bore, 15mm stroke, 10mm adjust code, G1/4 port and mounting. The MBLJ upgrades the body to a riveted rolling-packed design and changes the magnet switches from CS1-M/DS1-M to CMSG/DMSG/EMSG.
The -10 adjust code lets you trim up to 10mm at the rear, giving a usable stroke window of 5-15mm. The adjuster is a travel stop, not a load lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
Direct Upgrade
The MBLJ40X15-10-S replaces this model 1:1.
Fast Dispatch
MBLJ replacements are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Recommended AirTAC MBLJ Replacements
Request a Quote (Airtac MALJ40 Adjustable Mini Cylinder MALJ40X15-10-S → MBLJ40X15-10-S)
Tell us the quantity and destination — we quote the direct MBLJ40X15-10-S replacement with price, stock and lead time, usually within 7-8 hours.