Airtac PB Pen-type Cylinder PB10X15SCB
The AirTAC Airtac PB Pen-type Cylinder PB10X15SCB is a double-acting pen-size (mini) air cylinder with a Ø10mm bore and 15mm stroke. Its slim round barrel and back cover are stainless steel, the M5×0.8 ports keep plumbing compact, and the fast, low-friction piston suits high-cycle small-part handling.
- BoreØ10 mm
- Stroke15 mm
- Port sizeM5×0.8
- Acting typeDouble acting
- Rod threadM8×1.0
- CushionElastic bumper (both ends)
About the Airtac PB Pen-type Cylinder PB10X15SCB
The AirTAC PB10X15SCB is a double-acting JIS pen-size mini cylinder engineered for high-frequency small-part motion. It features a slim SUS304 stainless steel round barrel and piston rod, offering excellent durability in damp or mildly corrosive environments while keeping weight low for end-of-arm tooling. Delivering 39.3 N of push force at 0.5 MPa, it operates on a 0.15-0.7 MPa pressure range with an M5x0.8 air port.
This specific configuration includes a built-in piston magnet (S) for position sensing and a CB double clevis back cover for pivoting loads. The unit relies on a fixed TPU bumper at each end to decelerate the stroke over the final few millimeters. Because the Ø4 mm rod is designed purely for coaxial thrust, external guiding is recommended if side loads are present.
Airtac PB Pen-type Cylinder PB10X15SCB Technical Specifications
| Model | Airtac PB Pen-type Cylinder PB10X15SCB |
|---|---|
| Series | PB JIS pen-size mini cylinder |
| Bore size | Ø10 mm |
| Rod diameter | Ø4 mm |
| Stroke | 15 mm |
| Acting type | Double acting |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Cushion | Elastic bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC PB pen-size datasheet. Piston rod and barrel are stainless steel. Confirm bore, stroke and back-cover option against the product label before installation.
Theoretical Output Force (Ø10mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 39.3 N | 33.0 N |
| 0.7 MPa (max) | 55.0 N | 46.2 N |
Values are taken from the AirTAC PB thrust table. Because pull acts on the rod-side annular area, pull force is always lower than push. Actual usable force is reduced by friction — size with a margin.
Model Code: Airtac PB Pen-type Cylinder PB10X15SCB
| PB | JIS pen-size double-acting mini-cylinder series. |
|---|---|
| 10 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| CB / U / R | Back cover: CB double clevis, U 90° side inlet, R axial inlet (bore-dependent). |
Mounting accessories: LB, FA, CJ. Related PB-family variants: PSB (single-acting push), PTB (single-acting pull), PBD (double rod), PBJ (adjustable stroke), PBR (front-mount).
Where the Airtac PB Pen-type Cylinder PB10X15SCB Is Used
Pick-and-Place Ejection
Ideal for popping small electronic components out of test sockets on a high-speed PCB assembly line, utilizing the short 15 mm stroke and lightweight pen-size body.
Pouch Flap Folding
Provides the precise 39.3 N push at 0.5 MPa needed to tuck cardboard flaps on a compact packaging machine, with the CB double clevis accommodating the pivoting motion.
Lab Dispenser Actuation
Drives a micro-pneumatic dispensing valve for chemical reagents, where the SUS304 construction resists humidity and the built-in magnet confirms valve closure via a reed or electronic switch.
Is the Airtac PB Pen-type Cylinder PB10X15SCB the Right Cylinder?
When sizing this actuator, plan for a safe working load of roughly 24 N, which is about 60 percent of the 39.3 N theoretical push at 0.5 MPa, ensuring smooth travel after accounting for seal friction. For vertical lifts, this equates to raising approximately 2 kg safely with a 2:1 margin. If you need less force, stepping down to the Ø6 bore provides 14.2 N push at 0.5 MPa, while stepping up to the Ø12 bore yields 56.5 N for heavier tooling.
A standard PB-type cylinder drifts when air pressure is lost or the valve is centered, as the bumper only decelerates near the stroke end and does not function as a lock. For fail-safe holding, an external rod lock or mechanical stop is required. Confirm your ordering essentials: 10 mm bore, 15 mm stroke, M5x0.8 port, S magnet, CB double clevis.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Slim pen body vs. a standard round cylinder
- ✓ Back cover: CB / U / R inlet direction
- ✓ Magnet (S) for sensors?
- ✓ Mounting: LB / FA / CJ or front thread
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 0.7 MPa operating pressure.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
- check Fit dust caps to ports during long-term storage.
- check Installation by qualified personnel per AirTAC docs.
Airtac PB Pen-type Cylinder PB10X15SCB FAQ
At 0.5 MPa, the push force is 39.3 N and the pull force is 33 N. At the maximum operating pressure of 0.7 MPa, the push force is 55 N and the pull force is 46.2 N. The operating pressure range is 0.15-0.7 MPa, with a speed of 50-800 mm/s and a proof pressure of 1.2 MPa.
It uses a fixed TPU bumper at each end that decelerates the piston over the last few millimeters; it is not adjustable, so meter-out the exhaust or add an external shock absorber for high-speed loads. The CB back cover is a double clevis designed for pivoting loads, and the S option provides a magnet for AirTAC reed or electronic switches.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PB Pen-Size Cylinders
Request a Quote for Airtac PB Pen-type Cylinder PB10X15SCB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.