This model is discontinued
AirTAC has phased out the MAL series. The drop-in replacement is SAIJ80X225-75 — same bore, stroke, output force, port and mounting, so it fits the same application. Simply order the SAIJ80X225-75 in place of this model. The SAI replacement keeps the same ISO 15552 mounting interface, bore, stroke, output force and accessories, so it drops straight into existing fixtures. It is the current-production version of this cylinder with an upgraded piston seal.
Airtac SIJ80 Dual Axis Adjustable Cylinder SIJ80X225-75
The AirTAC Airtac SIJ80 Dual Axis Adjustable Cylinder SIJ80X225-75 is a double-acting ISO 15552 (orig. ISO 6431) profile-barrel cylinder with a Ø80mm bore and 225mm stroke, G3/8 air ports and adjustable end cushioning. This model is discontinued — the drop-in replacement is the SAIJ80X225-75, which matches its ISO interface, bore, stroke, force and mounting.
- BoreØ80 mm
- Stroke225 mm
- Port sizeG3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- StatusDiscontinued → SAIJ80X225-75
About the Airtac SIJ80 Dual Axis Adjustable Cylinder SIJ80X225-75
The AirTAC SIJ80X225-75 is a discontinued double-acting single-rod ISO 15552 adjustable-stroke cylinder. An external stop screw lets you trim the extend stroke by up to 75 mm on-site, yielding a usable 150-225 mm stroke. The 80 mm bore uses a G3/8 port, M20x1.5 rod thread, and 36 mm adjustable cushions. It delivers 2513 N push and 2268 N pull at 0.5 MPa, reaching 4523 N at 0.9 MPa.
The exact drop-in replacement is the SAIJ80X225-75, matching the interface, force, and port. The SAIJ family uses an upgraded two-piece Y-shaped piston seal for lower start-up pressure. Computed buyer insight: safe working load is roughly 1508 N (60% of the 0.5 MPa push), allowing a 128 kg vertical lift with a 2:1 margin. Note: this SKU lacks a magnet (-S) so it cannot take a switch.
Airtac SIJ80 Dual Axis Adjustable Cylinder SIJ80X225-75 Technical Specifications
| Model | Airtac SIJ80 Dual Axis Adjustable Cylinder SIJ80X225-75 |
|---|---|
| Series | SI ISO 15552 profile cylinder (discontinued) |
| Replacement | SAIJ80X225-75 |
| Bore size | Ø80 mm |
| Stroke | 225 mm |
| Acting type | Double acting |
| Port size | G3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SI datasheet (now discontinued). The SAIJ80X225-75 carries the same ISO 15552 ratings. Confirm against the product label before installation. Thread options: PT / G / NPT.
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
The SAIJ80X225-75 produces the same force from the same bore — a true drop-in on output. Actual usable force is lower than theoretical; size with a margin.
Model Code: Airtac SIJ80 Dual Axis Adjustable Cylinder SIJ80X225-75
| SI | ISO 15552 profile-barrel cylinder (discontinued). |
|---|---|
| 80 | Bore size in mm. |
| ×225 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Legacy SI-family variants: SID (double rod), SIJ (adjustable stroke) — each maps to its SAI equivalent (SID→SAID, SIJ→SAIJ). Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B).
Where the Airtac SIJ80 Dual Axis Adjustable Cylinder SIJ80X225-75 Is Used
Variable Pitch Indexing
Trimming the extend stroke by up to 75 mm on-site allows a single cylinder to drive multiple varying pitch lengths without swapping the entire actuator assembly.
Adjustable Transfer Pusher
Fine-tune the pusher end position between 150 and 225 mm to accommodate different package sizes on the fly, ensuring precise placement without mechanical spacers.
Dynamic Sealing Press
Dial in the exact 80 mm bore extend stop to apply consistent 2513 N force at 0.5 MPa for carton forming, preventing overtravel damage to delicate materials.
Replacing the Airtac SIJ80 Dual Axis Adjustable Cylinder SIJ80X225-75 with the SAIJ80X225-75
To replace the discontinued SIJ80X225-75, order the drop-in SAIJ80X225-75. When sizing both ways, the neighboring 63 mm bore yields 1559 N push at 0.5 MPa, while the 100 mm bore yields 3927 N. The 75 mm adjust window is ideal if your end position needs on-site tuning between 150 and 225 mm. Reuse your FA, LB, or TC ISO 15552 mounts. Because this SKU lacks the -S magnet, it cannot accept legacy CS1-B/DS1-B sensors; confirm external sensing needs. The external stop sets end position but is not a lock; for held loads use an external rod lock or SAIL/BSAI variant. For stroke lengths over 300 mm, carefully manage side loading.
Replacement checklist
- ✓ Same ISO 15552 interface → SAIJ80X225-75
- ✓ Same bore / stroke / force
- ✓ Port/thread type (PT/G/NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Mounting reused (FA/FB/CA/CB/CR/LB/TC)
Airtac SIJ80 Dual Axis Adjustable Cylinder SIJ80X225-75 FAQ
Yes, the SIJ80X225-75 is discontinued. The exact drop-in replacement is the SAIJ80X225-75. It matches the ISO 15552 interface, 80 mm bore, 225 mm stroke, 75 mm adjust window, G3/8 port, and 4523 N push force at 0.9 MPa.
The 80 mm bore delivers 2513 N push and 2268 N pull at 0.5 MPa, 3518 N at 0.7 MPa, and 4523 N at 0.9 MPa (513 kgf max). The external stop screw provides a 75 mm adjust window, shortening the 225 mm nominal extend stroke down to 150 mm. The stop sets end position and is not a load lock.
Related AirTAC SAI Cylinders
Request a Quote for the SAIJ80X225-75
Send us the quantity and destination. We confirm price, stock and lead time on the SAIJ80X225-75 replacement — usually within 7-8 hours.