Airtac TCM Triple Axis Cylinder TCM25X150SH
The AirTAC TCM Triple Axis Cylinder TCM25X150SH is a genuine JIS-standard guided cylinder with a Ø25mm bore and 150mm stroke on twin guide rods. Its integrated brass sliding bearing gives high radial-load and impact resistance — about double the horizontal impact tolerance of a plain cylinder, holding the tool square to ±0.08° of rotation without any external linear guide.
- BoreØ25 mm
- Stroke150 mm
- Port size1/8"
- BearingBrass sliding bearing
- Non-rotating±0.08°
- CushionRubber bumper
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TCM Triple Axis Cylinder TCM25X150SH
The AirTAC TCM25X150SH is a JIS-standard twin-rod guided cylinder with a brass sliding bearing. It generates 245 N of push and 189 N of pull at 0.5 MPa. The integrated twin guide rods eliminate the need for an external linear rail, directly absorbing side loads and torque. A ±0.08° non-rotating accuracy ensures your end-of-arm tooling stays perfectly square under offset loads, while the Ø12 mm piston rod and 1/8" PT ports provide robust plumbing and mechanical fit.
Built for harsh environments, the brass sleeve bearing shrugs off dust, grit, and hard impacts where a steel-ball guide would jam. It is double-acting, operating at 0.15-1.0 MPa with Viton (FKM) seals for higher temperature ranges. Stroke termination relies on fixed TPU rubber bumpers, meaning there is no adjustable air-cushion screw to tune. If air pressure drops, the rod will drift, so add an external rod lock for fail-safe positioning.
Airtac TCM Triple Axis Cylinder TCM25X150SH Technical Specifications
| Model | Airtac TCM Triple Axis Cylinder TCM25X150SH |
|---|---|
| Series | TCM JIS guided (twin-rod) cylinder |
| Bore size | Ø25 mm |
| Stroke | 150 mm |
| Acting type | Double acting |
| Bearing | Brass sliding bearing |
| Port size | 1/8" |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Non-rotating tolerance | ±0.08° (retracted) |
| Cushion | Rubber bumper |
| Max std stroke | Up to 250 mm |
Specifications follow the official AirTAC TCL/TCM series datasheet (JIS standard). Confirm against the product label before installation. Thread options: PT (blank) / G / NPT. Every TC model ships with a built-in magnet for sensor switches.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 189 N |
| 0.7 MPa | 344 N | — |
| Max | 50 kgf | |
Force is set by the bore and piston rod (Ø12 mm); the twin guide rods carry side load and torque, not thrust. Actual usable force is lower than theoretical due to friction and back-pressure.
Model Code: Airtac TCM Triple Axis Cylinder TCM25X150SH
| TC | Tri-rod (guided, twin-rod) cylinder, double acting. |
|---|---|
| M | Bearing: Brass sliding bearing (M = brass sliding). |
| 25 | Bore size in mm. |
| ×150 | Stroke length in mm. |
| S | Built-in magnet (standard on TC) for a magnetic sensor switch. |
Sister type: TCL25X150 (steel-ball linear bearing, lower friction & higher precision). Thread codes: blank = PT · G · T = NPT.
Where the Airtac TCM Triple Axis Cylinder TCM25X150SH Is Used
Sawmill Fence Positioning
Handles heavy wood pushing and gritty sawdust environments, using the 245 N thrust and brass sliding bearing that tolerates impacts where a ball guide would jam.
Off-Centre Gripper Slide
Maintains ±0.08° non-rotation accuracy to keep a gripper square during heavy side-loading, leveraging the twin guide rods to absorb moment torque.
Foundry Sand-Mould Push
Survives hot, dirty foundry duty with Viton FKM seals and a brass sleeve bearing that shrugs off grit while delivering 344 N of push at 0.7 MPa.
Is the Airtac TCM Triple Axis Cylinder TCM25X150SH the Right Cylinder?
This Ø25 bore provides 245 N of thrust at 0.5 MPa. If your application requires less force, the smaller Ø20 bore yields 157 N of push; for heavier radial loads, stepping up to the Ø32 bore gives 402 N. The standard S magnet is included for CS1 reed or DS1 electronic switches. Choose the sister TCL series with its steel-ball linear bearing only if you need low-friction precision for vertical high-load tasks. This 150 mm stroke is a standard length for this bore.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Side load / torque the guide must carry
- ✓ TCL (precision, low friction) vs TCM (impact, radial load)
- ✓ Stroke & mounting face (top / bottom / rear)
- ✓ Port/thread type (PT/NPT/G)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check The guide unit takes side load & torque — but do not exceed the max safe load/torque for your stroke.
- check Mount from the top, bottom (screw or T-slot) or rear face; use the precision locating holes.
- check Do not disassemble the fixing block or guide unit — factory-set precision.
- check Fit CS1 / DS1 magnetic switches in the four sensor slots as needed.
Airtac TCM Triple Axis Cylinder TCM25X150SH FAQ
It delivers 245 N push and 189 N pull at 0.5 MPa, and 344 N push at 0.7 MPa, with a theoretical maximum force of 50 kgf. The port size is 1/8" with a PT thread form.
No, stroke ends are damped by fixed TPU rubber bumpers rather than an adjustable air cushion. The standard built-in magnet works with CS1 reed and DS1 electronic switches in the four sensor slots.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC TCM Cylinders
Request a Quote for Airtac TCM Triple Axis Cylinder TCM25X150SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.