AirTAC 3V200M-14 3V-F Base (3V200M14F)
The AirTAC AirTAC 3V200M-14 3V-F Base (3V200M14F) is a genuine 3V-F manifold base manifold base for 14 stations on one shared air supply. A base is a machined block: it carries no coil and no solenoid, so the valves that sit on it are ordered separately.
- Valve type3/2-way (3-port, 2-position)
- Stations14
- Series3V-F manifold base
About the AirTAC 3V200M-14 3V-F Base (3V200M14F)
Fourteen stations make the AirTAC 3V200M14F the largest of the 3V200M bases in this kit - a single machined block that seats fourteen 3/2 solenoid valves on one shared supply. It has no coil and no electrical connection of its own; every electrical property belongs to the valves that occupy its positions, and those are ordered separately.
This is a genuine AirTAC part from the 3V2 family. On a new build it lets the designer fix one manifold location and size the wiring loom once; on a retrofit it replaces a scatter of individually plumbed valves with one block, freeing panel space and cutting pipe runs. Whatever you mount on it - NC or NO, any of the five family voltages, DIN plug or flying lead - we will verify the datasheet figures before you order. Send the RFQ and a person will answer.
AirTAC 3V200M-14 3V-F Base (3V200M14F) Technical Specifications
| Model | AirTAC 3V200M-14 3V-F Base (3V200M14F) |
|---|---|
| Series | 3V-F manifold base |
| Item form | Manifold base (no coil, no solenoid, no initial state) |
| Stations | 14 |
| Port size | Confirm from the datasheet — ask us |
| Thread | PT |
| Operating pressure | Confirm from the datasheet — ask us |
|---|---|
| Flow coefficient | Confirm from the datasheet — ask us |
| Temperature | Confirm from the datasheet — ask us |
| Protection | Confirm from the datasheet — ask us |
Model Code: AirTAC 3V200M-14 3V-F Base (3V200M14F)
| 3V-F manifold base | Body. |
|---|---|
| 14F | 14 stations in one assembly. |
| PT | Port thread. PT ships from stock; G and NPT are available to order. |
What a 3/2 Valve Does
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
Where the AirTAC 3V200M-14 3V-F Base (3V200M14F) Is Used
Control panel retrofit
Rebuilding an older machine whose valves are piped individually? A 14-station base lets the rebuilders group every 3/2 valve at one point and shorten the piping in a single visit.
Workshop valve bank
Maintenance teams keep a manifold on the bench to test or temporarily substitute 3/2 valves; fourteen positions mean a bank that mirrors a full machine section.
Multi-point blow-off
A plastics or food line that blows chips, dust or water from fourteen spots along the product path can run every blow valve from one base on one filtered feed.
Is the AirTAC 3V200M-14 3V-F Base (3V200M14F) the Right Part?
Fourteen positions suit machines with many small on/off air jobs: a row of blow-off nozzles, a set of part-present ejectors, or a bank of spring-return clamps. Match the valves to the job station by station - normally closed so a power cut vents the outlet, normally open so it keeps feeding, coil voltage matched to the control circuit, and flying-lead coils where the loom is pre-wired rather than socketed. Air to the base should still be filtered before it reaches any solenoid valve. We hold no published flow figures for this family, so ask us to check the datasheet against your actuators before ordering; the AirTAC 3V2 and 3V3 bodies are the alternative if you need published flow and coil power today, and double-acting cylinders belong on a 5-port 4V valve.
Confirm before you order
- ✓ Port size and thread (PT from stock; G / NPT to order)
- ✓ Initial state — NC or NO, ordered up front
- ✓ Coil voltage matches your controller output
- ✓ Electrical entry — DIN plug or flying lead
- ✓ Single valve, bare base, or complete assembly
- ✓ Single-acting duty, not double-acting
Installation & Wiring Notes
- check Use clean air filtered to 40µm or finer.
- check Use the manual override to test before powering up.
- check Leave the exhaust port clear, or fit a silencer.
- check Blank any unused station on the base before pressurising.
- check Wiring by qualified personnel, per AirTAC documentation.
AirTAC 3V200M-14 3V-F Base (3V200M14F) FAQ
For this base we confirm the station count and manifold arrangement. The pressure, flow, coil power and response figures belong to the 3/2 valves you mount on it; we do not hold published numbers for this family, so we verify them from the datasheet on request. If published flow and coil power are needed immediately, the AirTAC 3V2 and 3V3 valve bodies are the documented route.
Decide per station what must happen on power loss. A normally closed valve stops feeding the outlet when de-energised - right where losing air would drop a clamp or start an unwanted blow. A normally open valve keeps the outlet fed until energised - right for functions that must survive a control outage. Valves are ordered separately, so you can mix both on the same base.
Authorized Export Seller
Genuine AirTAC parts produced by the AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC 3V Valves
Request a Quote for AirTAC 3V200M-14 3V-F Base (3V200M14F)
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.