
The AirTAC 3V200M-17 3V-F Base (3V200M17F) is a genuine 3V-F manifold base manifold base for 17 stations on one shared air supply. A base is a machined block: it carries no coil and no solenoid, so the valves that sit on it are ordered separately.
The 3V200M17F is a machined manifold base from the AirTAC 3V200M range, drilled for seventeen valve stations fed from a single common air supply. A manifold of this size replaces up to seventeen individual valve connections with one threaded inlet, one wiring run along the base, and one mounting point on the machine frame. Each station accepts a 3/2 solenoid valve from the matching family, so a single panel can control seventeen separate single-acting cylinders, blow lines or clamp points while drawing from one supply.
We stock the 3V200M17F as a genuine AirTAC part and ship it worldwide. The valves themselves are ordered separately, which lets you mix normally closed and normally open versions, coil voltages and electrical entries on the same base. Datasheet figures for this base and its valves are not published on this page, but our team will confirm any dimension or performance question from the manufacturer datasheet when you send us an RFQ.
| Model | AirTAC 3V200M-17 3V-F Base (3V200M17F) |
|---|---|
| Series | 3V-F manifold base |
| Item form | Manifold base (no coil, no solenoid, no initial state) |
| Stations | 17 |
| Port size | Confirm from the datasheet — ask us |
| Thread | PT |
| Operating pressure | Confirm from the datasheet — ask us |
|---|---|
| Flow coefficient | Confirm from the datasheet — ask us |
| Temperature | Confirm from the datasheet — ask us |
| Protection | Confirm from the datasheet — ask us |
| 3V-F manifold base | Body. |
|---|---|
| 17F | 17 stations in one assembly. |
| PT | Port thread. PT is standard; G and NPT are available to order. |
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
A cartoning machine with seventeen single-acting clamp or pusher cylinders can run every station from one 3V200M17F base, giving the maintenance team a single air drop and one loom to check instead of seventeen loose valves and hoses.
On an assembly line where each jig position needs its own spring-return clamp, a 17-station base consolidates the valve control so individual stations can be swapped without disturbing neighbouring air circuits.
A bottling hall routing bottles between conveyors uses air-driven gates at many points; one manifold base mounted beside the line feeds all seventeen gate valves from a single filtered supply, simplifying fault-finding during a shift.
Seventeen stations is a large manifold, so plan the layout before ordering: check you have rail space for seventeen valve bodies, and decide which stations need NC and which need NO valves. The coil voltage is chosen per valve, not per base, so a DC24V panel can still run an AC110V valve on one station if that circuit demands it - each valve carries its own rating. Thread type on the common supply is PT as standard, with G and NPT available as order options. Because published flow figures for this family are not in our hands, send us your actuator sizes and we will confirm sizing against each station before you commit. If you would rather build the manifold from fully documented 3-port valves with published flow and coil power, the 3V2 and 3V3 bodies are the ones to ask about - and for any double-acting cylinder in the loop, you need a 5-port valve from the AirTAC 4V series instead.
Confirm before you order
This base is defined by its function and layout: 17 stations, PT standard thread, one shared supply. We hold no published flow or pressure figures for this family on this page, but we will read them from the manufacturer datasheet and confirm them with your RFQ. If you need a 3-port valve with figures published up front today, ask about the documented 3V2 and 3V3 bodies instead.
Yes, valves are ordered separately - the base carries no coil, so it has no voltage or power of its own. You can fill the seventeen stations with normally closed, normally open, any of the five coil voltages, and either DIN plug or flying-lead entry valves, which makes mixed-voltage panels straightforward. Remember a 3/2 valve feeds or vents a single outlet; it cannot drive a double-acting cylinder, which needs an AirTAC 4V 5-port valve.
Genuine AirTAC parts produced by the AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.