
The AirTAC 3V200M-20 3V-F Base (3V200M20F) is a genuine 3V-F manifold base manifold base for 20 stations on one shared air supply. A base is a machined block: it carries no coil and no solenoid, so the valves that sit on it are ordered separately.
The 3V200M20F is a machined manifold base for AirTAC 3V-series 3/2 solenoid valves. It carries twenty valves side by side on a single machined block, so one air supply and one wiring route serve the whole bank instead of twenty separate lines. A 3/2 valve has three ports - supply, outlet and exhaust - and two states: it either feeds air to the outlet or vents it, which is exactly what single-acting (spring-return) actuators, clamps and blow-off points need.
This listing is the base only: it has no coil, no voltage and no electrical state, and the valves that mount onto it are ordered separately. We stock the 3V2 family in both NC and NO versions, five coil voltages and two electrical entry types, so you can build the full twenty-station stack from one range. If you need a figure from the datasheet before committing, send us the RFQ and we will confirm it.
| Model | AirTAC 3V200M-20 3V-F Base (3V200M20F) |
|---|---|
| Series | 3V-F manifold base |
| Item form | Manifold base (no coil, no solenoid, no initial state) |
| Stations | 20 |
| Port size | Confirm from the datasheet — ask us |
| Thread | PT |
| Operating pressure | Confirm from the datasheet — ask us |
|---|---|
| Flow coefficient | Confirm from the datasheet — ask us |
| Temperature | Confirm from the datasheet — ask us |
| Protection | Confirm from the datasheet — ask us |
| 3V-F manifold base | Body. |
|---|---|
| 20F | 20 stations in one assembly. |
| PT | Port thread. PT is standard; G and NPT are available to order. |
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
Twenty 3/2 valves on one base suit a packaging conveyor where each lane has its own air-operated pusher or stopper, all fed and wired from one point.
A bank of spring-return clamps around a CNC fixture needs one 3/2 valve per clamp - a 20-station base keeps that manifold on a single block instead of a wall of fittings.
An automated test bench that lifts, clamps or vents at many points can mount all its 3/2 valves on this base, so a single supply serves the entire sequence.
Choosing the 3V200M20F over twenty individually plumbed valves buys you one consolidated air feed and one wiring loom, which makes leaks and electrical faults far easier to isolate during maintenance. The thread standard on this family is PT; G and NPT are available as order options if your pipework needs them. Remember to order the valves themselves - twenty of them for this base - and to match each coil voltage to your panel supply, because a coil cannot be changed by rewiring.
One honest note before you order: we do not hold the published flow and coil-power figures for the 3V1x0/3V2x0/3V3x0 family in hand, so ask us to check sizing against your actuators via the RFQ before you commit. If you need a fully specified 3-port valve today, the AirTAC 3V2 and 3V3 bodies have published flow and coil-power figures you can design from. And if any actuator on this manifold is double-acting, it cannot be driven by a 3/2 valve - that job belongs to the 5-port AirTAC 4V series.
Confirm before you order
We do not hold the datasheet for the 3V1x0/3V2x0/3V3x0 family in hand, so we will not print numbers we cannot stand behind - send us the RFQ and we will confirm the pressure range, flow and coil power you need. If you require published figures right now, the AirTAC 3V2 and 3V3 bodies are the fully documented 3-port series to design from.
No - this listing is the 20-station manifold base only; every valve that mounts on it is ordered separately, chosen with the NC or NO state and coil voltage your panel needs. The 3/2 valves it carries suit single-acting spring-return cylinders, clamps and blow points. A double-acting cylinder needs two outlet ports, so it cannot run from a 3/2 valve - use the AirTAC 4V 5-port series for that.
Genuine AirTAC parts produced by the AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.