
The AirTAC 3V-F Base 3V200M4F is a genuine 3V-F manifold base manifold base for 4 stations on one shared air supply. A base is a machined block: it carries no coil and no solenoid, so the valves that sit on it are ordered separately.
The 3V200M4F is a genuine AirTAC 4-station manifold base, machined to carry four 3/2 solenoid valves on a single block. A 3/2 valve has three ports - supply, outlet and exhaust - and two states: energised it feeds the outlet, de-energised it vents it. Mounting several of those valves side by side on one base means one air feed, one mounting footprint and one wiring route for the whole group.
This listing is for the base only: the coils, switching states and voltages belong to the valves you bolt onto it, and those are ordered separately. We stock the full family around it - normally closed and normally open valves, five coil voltages, DIN plug and flying-lead entries - so you can populate all four stations from one order. If you need a datasheet figure confirmed before you commit, send us the RFQ and we will answer it from the datasheet rather than guess.
| Model | Airtac 3V-F Base 3V200M4F |
|---|---|
| Series | 3V-F manifold base |
| Item form | Manifold base (no coil, no solenoid, no initial state) |
| Stations | 4 |
| Port size | Confirm from the datasheet — ask us |
| Thread | PT |
| Operating pressure | Confirm from the datasheet — ask us |
|---|---|
| Flow coefficient | Confirm from the datasheet — ask us |
| Temperature | Confirm from the datasheet — ask us |
| Protection | Confirm from the datasheet — ask us |
| 3V-F manifold base | Body. |
|---|---|
| 4F | 4 stations in one assembly. |
| PT | Port thread. PT is standard; G and NPT are available to order. |
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
One base carries the four valves that switch spring-return clamps around a machining fixture, so every clamp shares a single regulated air feed and releases to exhaust together on power loss if NC valves are fitted.
On/off air blow is a natural 3/2 job. A 4-station base lets one packaging machine run separate blow-off points over four product tracks from one consolidated supply instead of four scattered individual valves.
Machine builders fitting several 3/2 functions inside one panel use a manifold base to keep the pneumatic plumbing in one block and the wiring loom on one route, which shortens both the build and later fault-finding.
A 4-station base suits a machine that switches four or fewer 3/2 functions from one place - a set of single-acting clamps, several blow points, a group of spring-return actuators. Consolidating them on one shared supply simplifies both the pneumatic layout and fault-finding: one feed to check, one block to remove. Order four valves separately and match their coil voltage to your panel supply, since a coil is bought for one voltage and cannot be rewired to another; choose NC where the safe state on power loss is vented, NO where it is fed. Thread here is PT as standard, with G and NPT available as order options. Sizing needs care: published flow and coil-power figures for this family are not in our hands, so ask us to confirm the base and its valves against your actuators before ordering. If you want a fully documented 3-port valve today, the AirTAC 3V2 (1/8in and 1/4in) and 3V3 (1/4in) bodies have published flow and coil-power figures - by name, from their own datasheets. And if any actuator on the group is double-acting, that one needs a 5-port valve from the AirTAC 4V series instead.
Confirm before you order
Those belong to the valves, not the base, and for this family we confirm them from the datasheet on request rather than publish numbers we cannot stand behind. If you need published figures in hand today, the AirTAC 3V2 and 3V3 bodies have documented flow and coil-power data - ask us and we will match one to your actuator.
No and no. This listing is the machined 4-station base alone - no coils, no voltage, no switching state - so you order four 3/2 valves separately and populate it in your chosen NC or NO, voltage and electrical entry. A 3/2 valve cannot drive a double-acting cylinder in either direction; that job needs a 5-port valve from the AirTAC 4V series.
Genuine AirTAC parts produced by the AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.