
The AirTAC 3V-F Base 3V200M7F is a genuine 3V-F manifold base manifold base for 7 stations on one shared air supply. A base is a machined block: it carries no coil and no solenoid, so the valves that sit on it are ordered separately.
The 3V200M7F is a machined manifold base with seven valve stations. Valves mounted on it share one common air supply instead of each needing its own individual feed and fittings. That consolidation shortens the piping run, cuts the number of supply connections to build and maintain, and puts all seven valves in one place so a faulty one can be found and swapped quickly.
We stock this base as a genuine AirTAC part, and the code tells you the size plainly: 7F means seven stations. The valves themselves are ordered separately, so choose the NC or NO state, coil voltage and electrical entry each station needs and order one valve per position. If you want any figure for the base or its valves checked before you commit, send the RFQ and we will read it back to you straight from the datasheet.
| Model | Airtac 3V-F Base 3V200M7F |
|---|---|
| Series | 3V-F manifold base |
| Item form | Manifold base (no coil, no solenoid, no initial state) |
| Stations | 7 |
| Port size | Confirm from the datasheet — ask us |
| Thread | PT |
| Operating pressure | Confirm from the datasheet — ask us |
|---|---|
| Flow coefficient | Confirm from the datasheet — ask us |
| Temperature | Confirm from the datasheet — ask us |
| Protection | Confirm from the datasheet — ask us |
| 3V-F manifold base | Body. |
|---|---|
| 7F | 7 stations in one assembly. |
| PT | Port thread. PT is standard; G and NPT are available to order. |
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
A CNC fixture with up to seven spring-return swing clamps, each clamp fed and vented by its own 3/2 valve seated on the one shared base.
A panel builder mounting seven valves behind a single cabinet door, with one air feed entering the base and one tidy wiring loom serving every coil.
A packaging line where several stations need an on/off air signal - diverters, product stoppers and short blow-off nozzles - all supplied from one 7-station base.
A base earns its place when a machine needs several 3/2 valves side by side: seven stations on one shared feed means one air preparation point instead of seven, and one wiring loom instead of seven separate drops into the cabinet. Note that the base has no coil of its own, so it carries no voltage and no switching state - those decisions belong to the valves you order onto it. Pick NC valves where an outlet must vent on power loss, or NO where air must keep flowing through a failure.
Sizing still matters, so ask us to confirm the datasheet figures against your actuators before you order. If your project needs a 3-port valve with published flow and coil-power data in hand today, the documented AirTAC 3V2 (1/8" and 1/4") and 3V3 (1/4") bodies carry those figures. And if the real job is a double-acting cylinder, that is an AirTAC 4V series requirement, not a 3/2 one.
Confirm before you order
We do not hold a published specification sheet for this family, so the page quotes no numbers. Send the RFQ and we will confirm the datasheet figures you need for your build. If your project requires published flow and coil-power data up front, the AirTAC 3V2 (1/8" and 1/4") and 3V3 (1/4") bodies are the fully documented alternatives.
No - the 3V200M7F is the manifold block only, with seven stations and no coil, so it has no voltage and no NC or NO state of its own. Order one 3/2 valve per station, choosing NC or NO to suit your fail-safe requirement, the coil voltage that matches your panel supply, and DIN plug or flying-lead entry.
Genuine AirTAC parts produced by the AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.