
The AirTAC 3V-F Base 3V200M9F is a genuine 3V-F manifold base manifold base for 9 stations on one shared air supply. A base is a machined block: it carries no coil and no solenoid, so the valves that sit on it are ordered separately.
The 3V200M9F is a machined manifold base in the AirTAC 3V family, drilled for nine valve stations fed from one common air supply. A base itself contains no coil, no voltage and no moving parts - it is the mounting block that carries a row of 3/2 solenoid valves so they share a single air inlet and a single wiring route instead of nine separate connections.
We stock the 3V200M9F as a genuine AirTAC part. The valves that sit on it are ordered separately, so you can mix normally closed and normally open stations, any of the five standard coil voltages and either electrical entry across the same base. If you need a datasheet figure for the matching valves before you commit, tell us what you are driving and we will confirm it for you.
| Model | Airtac 3V-F Base 3V200M9F |
|---|---|
| Series | 3V-F manifold base |
| Item form | Manifold base (no coil, no solenoid, no initial state) |
| Stations | 9 |
| Port size | Confirm from the datasheet — ask us |
| Thread | PT |
| Operating pressure | Confirm from the datasheet — ask us |
|---|---|
| Flow coefficient | Confirm from the datasheet — ask us |
| Temperature | Confirm from the datasheet — ask us |
| Protection | Confirm from the datasheet — ask us |
| 3V-F manifold base | Body. |
|---|---|
| 9F | 9 stations in one assembly. |
| PT | Port thread. PT is standard; G and NPT are available to order. |
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
A machining fixture with several spring-return clamp cylinders needs one 3/2 valve per clamp. Mount them all on one 3V200M9F so the cell builder lands a single air feed and a single cable run instead of nine loose valves taped to the frame.
A cartoning machine that puffs product pockets clear before loading uses short on/off air blasts at several positions. A manifold of 3/2 valves on this base gives each blow point its own solenoid control from one supply.
A conveyor sorting station that kicks rejected parts with small single-acting air cylinders can drive every gate from one manifold row, with each valve wired back to the PLC through the same tidy route.
Choose a 3V200M9F when your panel needs several 3/2 valves in one place - a machine with multiple clamps, blow points or single-acting actuators rewards you with one air feed to fit, one wiring loom to route and one place to look when a station misbehaves. Count the valves you need today and allow a spare station or two; the base has nine.
Remember that a base is only half the order: pick the valves themselves from the 3V2 family and specify NC or NO, coil voltage and entry for each station. Because we do not hold published flow figures for this family in hand, send us your actuator sizes and we will check the match before you buy. If you would rather have a fully documented 3-port valve from the start, the AirTAC 3V2 and 3V3 bodies carry published flow and coil-power data, and a double-acting cylinder needs the 5-port AirTAC 4V series instead.
Confirm before you order
We do not publish pressure, flow or electrical figures for this family, so we will not guess them. Ask us with your actuator details and we will confirm the numbers from the datasheet before you order. If you need a 3-port valve with published flow and coil-power figures today, the AirTAC 3V2 and 3V3 bodies are fully documented alternatives.
No - the base is the manifold block only. You order the 3/2 valves separately and choose normally closed or normally open, the coil voltage that matches your panel supply, and DIN plug or flying-lead entry for each station. Note that 3/2 valves suit single-acting cylinders; a double-acting cylinder needs a 5-port valve from the AirTAC 4V series.
Genuine AirTAC parts produced by the AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.