
The AirTAC 3V300M-10 3V-F Base (3V300M10F) is a genuine 3V-F manifold base manifold base for 10 stations on one shared air supply. A base is a machined block: it carries no coil and no solenoid, so the valves that sit on it are ordered separately.
A 3/2 valve manifold base is a single machined block that mounts ten 3-port 2-position valves onto one shared air supply. Instead of ten separate valves each needing their own feed fitting, supply tubing and wiring run, the 3V300M10F carries them side by side on a common internal gallery: one air inlet, one wiring loom, ten individually controlled valve positions. A 3/2 valve itself has three ports - supply, outlet and exhaust - and two states, feeding the outlet or venting it.
The 3V300M10F is a base only: it has no coil, no voltage rating and no initial state of its own, because those belong to the valves fitted to it. Valves are ordered separately and can be mixed on the same base - any combination of NC and NO, any of the five coil voltages, and either electrical entry across the family. It is a genuine AirTAC part we stock. Pressure, flow and coil-power figures for the mating valves are not published on this page; we will pull them from the datasheet and confirm them with your quotation.
| Model | AirTAC 3V300M-10 3V-F Base (3V300M10F) |
|---|---|
| Series | 3V-F manifold base |
| Item form | Manifold base (no coil, no solenoid, no initial state) |
| Stations | 10 |
| Port size | Confirm from the datasheet — ask us |
| Thread | PT |
| Operating pressure | Confirm from the datasheet — ask us |
|---|---|
| Flow coefficient | Confirm from the datasheet — ask us |
| Temperature | Confirm from the datasheet — ask us |
| Protection | Confirm from the datasheet — ask us |
| 3V-F manifold base | Body. |
|---|---|
| 10F | 10 stations in one assembly. |
| PT | Port thread. PT is standard; G and NPT are available to order. |
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
A machining cell with ten spring-return clamps can place one 3/2 valve per clamp on a single 3V300M10F, so each fixture closes and vents independently while sharing one air feed and one cable run.
A board-handling machine using suction cups at several stations can group its 3/2 valve functions on one manifold base, cutting panel space and making individual station faults easy to isolate.
A packaging machine that ejects dust and trim from ten points on the line can drive each point from its own valve position on the base, with each nozzle controlled separately from one shared supply.
Choose the 3V300M10F when a machine needs ten or more 3/2 valve functions in one place: multiple single-acting clamps, a bank of blow-off nozzles, or a row of spring-return actuators. The manifold wins on wiring and fault-finding - one air feed and one harness instead of ten - and a faulty valve can be swapped at a single station without disturbing the rest of the panel's plumbing. Count your stations before ordering: if you need fewer, the same family covers other station counts in the 3V-F range.
Note what the base does not do: it does not include the valves, and it does not turn a 3/2 arrangement into a double-acting-cylinder circuit - that requires a 5-port valve, which is the AirTAC 4V series. Since published flow figures for this family are not in our hands, send us the actuator sizes you intend to drive and we will confirm valve sizing against them before you order. If you would rather start from a fully specified single valve today, the documented AirTAC 3V2 and 3V3 direct-acting bodies have published flow and coil-power figures.
Confirm before you order
The 3V300M10F takes 3/2 valves from the 3V3x0 family in the matching body, ordered separately - you choose NC or NO, the coil voltage and the electrical entry per station. We do not publish flow or pressure figures for this family on the site; ask us with your RFQ and we will confirm them from the datasheet. If you need published figures immediately, the AirTAC 3V2 and 3V3 direct-acting valve bodies are fully documented alternatives.
One machined base gives you one air inlet, one mounting and one wiring route for all ten positions, which means fewer fittings, a tidier panel and faster fault-finding - a failed valve is swapped at one station while the rest keep running. Remember the base carries no coil or state itself, and a 3/2 circuit on it feeds single-acting (spring-return) actuators; for double-acting cylinders you need a 5-port AirTAC 4V valve.
Genuine AirTAC parts produced by the AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.