
The AirTAC 3V-F Base 3V300M2F is a genuine 3V-F manifold base manifold base for 2 stations on one shared air supply. A base is a machined block: it carries no coil and no solenoid, so the valves that sit on it are ordered separately.
The 3V300M2F is a machined manifold base in the AirTAC 3V-F range, drilled for two 3/2 solenoid valves on a single block. A 3/2 valve has three ports - supply, outlet and exhaust - and two states: it either feeds air to the outlet or vents it, which is exactly what a single-acting (spring-return) cylinder, an air blow-off nozzle or a pilot stage needs. On a base, both valves share one air supply and one wiring run instead of each carrying its own.
This listing is for the base only: it has no coil, no voltage and no switching state. The valves that sit on it are ordered separately, and each can be chosen as normally closed or normally open, in AC220V, DC24V, AC110V, AC24V or DC12V, with a DIN plug or a flying lead. It is a genuine AirTAC part. Pressure, flow and coil-power figures for the matched valves are not published on this page - send the RFQ and we will confirm them from the datasheet.
| Model | Airtac 3V-F Base 3V300M2F |
|---|---|
| Series | 3V-F manifold base |
| Item form | Manifold base (no coil, no solenoid, no initial state) |
| Stations | 2 |
| Port size | Confirm from the datasheet — ask us |
| Thread | PT |
| Operating pressure | Confirm from the datasheet — ask us |
|---|---|
| Flow coefficient | Confirm from the datasheet — ask us |
| Temperature | Confirm from the datasheet — ask us |
| Protection | Confirm from the datasheet — ask us |
| 3V-F manifold base | Body. |
|---|---|
| 2F | 2 stations in one assembly. |
| PT | Port thread. PT is standard; G and NPT are available to order. |
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
A small milling or drilling fixture with two spring-return clamps: one valve per clamp, both fed from a single regulator and vented together when the cycle ends.
Two large pneumatic process or tank valves that each need a small 3/2 pilot signal, mounted side by side on one base for tidier tubing.
A compact packaging table using short air blasts to clear dust from two filling positions before the trays are sealed.
Two stations suit a small machine or a bench rig where one or two spring-return cylinders or blow lines run off one supply. Order each valve separately: pick NC when the outlet must go dead and vent on power loss, NO when it must stay fed; match the coil voltage to the control panel, because a coil cannot be rewired to another voltage; choose DIN plug or flying lead to suit the wiring. Because flow figures for this 3V1 family are not in our hands, ask us to check sizing against your actuator before ordering. If you need a 3-port valve with published flow and coil power today, the documented AirTAC 3V2 and 3V3 bodies carry full figures. A double-acting cylinder is out of reach for any 3/2 valve - that calls for a 5-port AirTAC 4V.
Confirm before you order
They live in the datasheets of the valves you mount on it, not on the base itself, and they are not published on this page. Tell us the valve codes and your supply conditions on the RFQ and we will confirm pressure range, flow and coil draw from the datasheet. If you need figures printed on the page today, the AirTAC 3V2 and 3V3 series are documented 3-port bodies with full published data.
Two 3V1-family 3/2 valves in the state (NC or NO), coil voltage (A to F) and electrical entry (DIN plug or flying lead) your panel needs. The base supplies air to both; it carries no coil or state of its own. Note that no 3/2 valve can drive a double-acting cylinder - use an AirTAC 4V 5-port valve for that.
Genuine AirTAC parts produced by the AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.