
The AirTAC 3V210-08 Solenoid Valve, 3V200 Series (3V21008NCA-AM) is a genuine 3-port 2-position (3/2) solenoid valve with 1/4 in ports. A 3/2 valve either feeds its outlet or vents it to exhaust, so it suits single-acting cylinders, air blow, clamping, vacuum switching and pilot duty. Its published figures are confirmed from the AirTAC datasheet on request.
The 3V21008NCA-AM is a 3/2-way solenoid valve from AirTAC with three ports - supply, outlet and exhaust - and two states. It is configured normally closed, so the outlet sees no air until the coil is energised, and the outlet is vented to exhaust once power drops. The 1/4in PT port gives a step up from a 1/8in connection, and the AC220V coil is meant for a standard mains control panel.
This is a genuine AirTAC part. Within the 3V family you can order normally closed or normally open, five coil voltages (AC220V, DC24V, AC110V, AC24V, DC12V), DIN plug or flying-lead entry, and manifold bases for multi-valve builds. Pressure range and flow for this kit are not in our published documentation, so attach a datasheet request to your RFQ and we will confirm the figures directly.
| Model | AirTAC 3V210-08 Solenoid Valve, 3V200 Series (3V21008NCA-AM) |
|---|---|
| Series | 3V210 |
| Valve type | 3/2-way (3-port, 2-position) |
| Initial state | Normally closed |
| Port size | 1/4 in |
| Thread | PT |
| Coil voltage | AC220V |
|---|---|
| Electrical entry | DIN plug (DIN socket type) |
| Coil power | Confirm from the datasheet — ask us |
| Operating pressure | Confirm from the datasheet — ask us |
| Flow coefficient | Confirm from the datasheet — ask us |
| Temperature | Confirm from the datasheet — ask us |
| Protection | Confirm from the datasheet — ask us |
| 3V210 | Body. |
|---|---|
| 1/4 in | Port size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in. |
| NC | Normally closed: no air at the outlet until the coil is energised. |
| AC220V | Coil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V. |
| — | Electrical entry: I = flying lead, otherwise a DIN plug. |
| PT | Port thread. PT ships from stock; G and NPT are available to order. |
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
Energise the coil to close a single-acting clamp cylinder on the workpiece; lose power and the spring retracts the clamp while the valve vents the line.
A momentary mains signal opens the outlet to the air line and clears swarf from the cut; de-energising vents the circuit rather than leaving it pressurised.
Use the 1/4in outlet to send an air signal to a bigger pneumatically actuated line valve, then dump that signal to exhaust on shutdown.
Choose the state first. Normally closed suits a job where air must stop at the outlet on power loss; normally open suits one where flow must persist. Both exist in this family. Then match the coil: this SKU's AC220V coil must see AC220V - a coil cannot be rewired to another voltage, it is ordered that way. Entry here is a DIN plug, so your panel supplies the socket; flying-lead versions exist if pre-wired leads suit the build better. If you are valving several of these on one machine, a 3V-F manifold base carries them on a shared air supply. For sizing, our documentation for this kit carries no flow figures, so ask us to check the valve against your cylinder before ordering; the documented AirTAC 3V2 and 3V3 bodies publish flow and coil power today if you need numbers immediately. A double-acting cylinder needs a 5-port 4V valve instead.
Confirm before you order
We confirm the pressure range, flow and coil power from the AirTAC datasheet when you enquire - none of those figures are published on this page. If you need published numbers today, the AirTAC 3V2 and 3V3 three-port bodies carry documented flow and coil-power data.
No. A 3/2 valve feeds or vents one outlet, which suits single-acting spring-return cylinders and blow lines. A double-acting cylinder needs pressure on both sides, so specify a 5-port AirTAC 4V valve for that duty.
Genuine AirTAC parts produced by the AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity, coil voltage and destination. We confirm price, stock and lead time — usually within 7-8 hours.