
The AirTAC ACEJ12 Adjustable Compact Cylinder ACEJ20X30-20B is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø20mm bore and 30mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
The ACEJ20X30-20B is a double acting AirTAC compact cylinder to ISO 21287 with an adjustable extend stroke. A stop screw on the body trims the 30 mm stroke down by up to 20 mm on site, giving a usable range of 10-30 mm without changing the cylinder. At 0.5 MPa this 20 mm bore pushes 157.1 N and pulls 117.8 N, and the male rod thread (B code) bolts straight to tooling. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight fixtures and guarding.
The hard-anodized aluminium body carries an S45C hard-chrome rod, a fixed TPU bumper at each end absorbs end-of-stroke shock, and the piston seal stores grease for long service. Speed range is 30-500 mm/s at 0.15-1.0 MPa (22-145 psi). Note: no magnet is fitted on this model - order the -S code if you need CMSE / DMSE switch sensing.
| Model | Airtac ACEJ12 Adjustable Compact Cylinder ACEJ20X30-20B |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø20 mm |
| Stroke | 30 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 118 N |
| 0.7 MPa | 165 N |
| Max (@1.0 MPa) | 24 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 20 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| -20 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
About 94 N of usable force at 0.5 MPa presses bushings into 3D-printed or moulded housings without damaging the part.
With the optional -S magnet ordered, CMSE or DMSE switches confirm the 30 mm gate motion on PCB test fixtures where a full-length cylinder will not fit.
The stop screw is a mechanical end stop only - it shortens the extend stroke and does not hold a load if air is lost. FA flange or LB foot mounts plus I/Y rod knuckles attach to the ISO 21287 face; add the -S magnet code if position switches are planned later.
Quick checklist
At 0.5 MPa it pushes 157.1 N and pulls 117.8 N; at 0.7 MPa push is 219.9 N and pull 164.9 N, with a theoretical maximum of 32 kgf at 1.0 MPa. The -20 code is a 20 mm adjustment window: an external stop screw shortens the 30 mm extend stroke by up to 20 mm, so the working range is 10-30 mm. It is double acting, runs 30-500 mm/s at 0.15-1.0 MPa (22-145 psi), and the rod end is a male thread (B code) with a PT port thread.
It is an ISO 21287 compact cylinder whose short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a hard-anodized aluminium body, S45C hard-chrome rod and fixed TPU bumpers at both ends. Sensing is not included: the magnet is the optional -S code, and only with -S can CMSE / DMSE switches be mounted. FA flange, LB foot and I/Y rod knuckles bolt to the standard ISO 21287 face.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.