
The AirTAC ACEJ12 Adjustable Compact Cylinder ACEJ20X35-20SB is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø20mm bore and 35mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
A double acting ISO 21287 compact cylinder with an adjustable extend stroke, the ACEJ20X35-20SB pairs a 20 mm bore with a 35 mm stroke and a male (B code) rod thread. The external stop screw trims the extend stroke anywhere inside the ordered 20 mm window, so the usable range is 15-35 mm, set on site with a screwdriver rather than a new order.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it slots into tight pick-and-place gantries and guarded fixtures. The hard-anodized aluminium body carries a 10 mm S45C hard-chrome rod, fixed TPU bumpers sit at both ends, and because this model carries the optional -S magnet, CMSE or DMSE switches can be clamped straight into the body slots.
| Model | Airtac ACEJ12 Adjustable Compact Cylinder ACEJ20X35-20SB |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø20 mm |
| Stroke | 35 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 118 N |
| 0.7 MPa | 165 N |
| Max (@1.0 MPa) | 24 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 20 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| -20 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
With the -S magnet fitted, CMSE or DMSE switches confirm the clamp is fully extended on an assembly jig, while the short body fits inside the fixture plate where a full-length profile cylinder would not.
Pushing cartons or blister packs off a conveyor at 30-500 mm/s suits the 20 mm bore's force class, and the male rod thread takes a Y knuckle for a quick-change pusher plate.
Check the load both ways before committing. Remember the stop screw is a mechanical end stop only: on air loss the piston drifts, so it is not a mid-stroke lock or load holder.
This unit ships with the -S magnet fitted and a male rod thread, PT ports (1/8" on this bore), and accepts FA flange or LB foot mounts plus I and Y rod knuckles on the ISO 21287 face. Speed range is 30-500 mm/s across 0.15-1.0 MPa (22-145 psi) of clean, 40 um filtered air.
AirtacDistr lists every ACEJ20 order code with its price on one page at https://airtacdistr.com/products/airtac-acej20-adjustable-double-rod-compact-cylinder
Quick checklist
The 20 mm bore runs on 0.15-1.0 MPa (22-145 psi) air filtered to 40 um, proof pressure 1.5 MPa (215 psi), temperature -20 to +70 C, speed 30-500 mm/s, with a 10 mm hard-chrome rod and 1/8" ports. The stop screw shortens the 35 mm extend stroke by up to 20 mm, giving a 15-35 mm working range.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits shallow fixtures and guarded frames. A fixed TPU bumper at each end absorbs end-of-stroke impact; it decelerates only and never holds a load. FA flange and LB foot mounts plus I/Y rod knuckles bolt to the standard face, and because this model carries the optional -S magnet, CMSE or DMSE reed or solid-state switches mount directly in the body slots.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.