
The AirTAC ACEJ12 Adjustable Compact Cylinder ACEJ20X75-20B is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø20mm bore and 75mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
A double acting ISO 21287 compact cylinder with an adjustable extend stroke, the ACEJ20X75-20B pairs a 20 mm bore with a 75 mm stroke and a male-threaded rod end (the B code). An external stop screw trims the extend stroke on site anywhere in the ordered 20 mm window, so the usable extend range is 55-75 mm without changing the valve or plumbing.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it slots into slim fixtures, guarding and gantry axes. The hard-anodized aluminium body carries an S45C hard-chrome rod, fixed TPU bumpers absorb end-of-stroke energy, and speed spans 30-500 mm/s at 0.15-1.0 MPa (22-145 psi).
| Model | Airtac ACEJ12 Adjustable Compact Cylinder ACEJ20X75-20B |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø20 mm |
| Stroke | 75 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 118 N |
| 0.7 MPa | 165 N |
| Max (@1.0 MPa) | 24 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 20 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -20 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
The 55-75 mm adjustable extend range lets a machinist dial in clamp travel per fixture, with 157.1 N at 0.5 MPa enough to hold small aluminium parts during light milling.
A 75 mm stroke nudges cartons or blisters off a conveyor lane, and the 20 mm trim window absorbs lane-width changes without re-piping the 1/8" ports.
About 8 kg of vertical lift capacity with margin suits gentle sample pressing or vial capping stations where the compact body must fit inside a benchtop enclosure.
Note that the stop screw is a mechanical end stop for the extend stroke, not a mid-stroke lock, so the rod can still drift if air is lost. This unit has no magnet; if you need CMSE or DMSE switch position feedback, order the -S variant instead. FA flange, LB foot and I/Y rod knuckles bolt to the standard ISO 21287 face.
Quick checklist
The -20 code sets a 20 mm adjustment window: an external stop screw shortens the 75 mm extend stroke on site, giving a usable range of 55-75 mm. It runs double acting on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, with fixed TPU bumpers at both ends.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits tight guards and gantries. This model has no magnet fitted; the optional -S code adds one so CMSE or DMSE switches can sense position. FA flange, LB foot and I/Y rod knuckles mount on the standard face, and the male rod thread (B code) takes standard tooling plates.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.