
The AirTAC ACEJ12 Adjustable Compact Cylinder ACEJ20X75-30B is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø20mm bore and 75mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
A double acting ISO 21287 compact cylinder, the ACEJ20X75-30B pairs a 20 mm bore with a 75 mm stroke that an external stop screw trims on site by up to 30 mm, giving a usable extend range of 45-75 mm. At 0.5 MPa it pushes 157.1 N and pulls 117.8 N; at 0.7 MPa those rise to 219.9 N and 164.9 N. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight fixtures where a full-length body cannot.
The hard-anodized aluminium body carries a hard-chrome plated S45C rod, a fixed TPU bumper sits at both ends, and the B code gives a male rod thread. Note that the adjuster is a mechanical end stop only: on air loss the piston still drifts, so it never holds a load. The magnet is the optional -S code, so this unit has none and no CMSE / DMSE switch can be fitted.
| Model | Airtac ACEJ12 Adjustable Compact Cylinder ACEJ20X75-30B |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø20 mm |
| Stroke | 75 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 118 N |
| 0.7 MPa | 165 N |
| Max (@1.0 MPa) | 24 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 20 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -30 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
The 45-75 mm adjustable extend range lets one cylinder serve several part heights on a bench-top press, with 157.1 N at 0.5 MPa enough to push light components off a nest.
Male rod thread (B code) accepts a custom gate arm, and the short ISO 21287 body fits under low conveyor frames where an ISO 15552 profile cylinder would not clear.
Choose the -30 window only if the trimmed stroke range of 45-75 mm matches your fixture, and remember the stop screw shortens the extend stroke rather than lengthening it. FA flange or LB foot mounts bolt to the ISO 21287 face, and if position feedback matters later, order the -S variant so CMSE / DMSE switches work.
Quick checklist
Push is 157.1 N and pull 117.8 N at 0.5 MPa; at 0.7 MPa push is 219.9 N and pull 164.9 N, with a theoretical maximum of 32 kgf at 1.0 MPa. It is double acting with a 75 mm stroke adjustable down to 45 mm via the -30 stop screw, runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), temperature -20 to +70 C, speed 30-500 mm/s, port 1/8", rod 10 mm with male thread, and a fixed TPU bumper at both ends.
An external stop screw shortens the extend stroke by up to 30 mm within the ordered window, so the effective range is 45-75 mm; it is a mechanical end stop, not a mid-stroke lock, so the rod still drifts if air is lost. Sensors need the optional -S magnet code, which this model does not carry, so no CMSE or DMSE switch can be mounted on this unit. Mounting uses the standard ISO 21287 face with FA flange or LB foot options.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.