
The AirTAC ACEJ12 Adjustable Compact Cylinder ACEJ20X80-20B is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø20mm bore and 80mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
A double acting ISO 21287 compact cylinder, the ACEJ20X80-20B pairs a 20 mm bore with an 80 mm stroke and a male-threaded rod end (the B code). Air drives the piston both ways, and an external stop screw trims the extend stroke anywhere within the ordered 20 mm window, giving a usable range of 60-80 mm. The hard-anodized aluminium body with an S45C hard-chrome-plated rod keeps the envelope short: roughly 50% less mounting length than an ISO 15552 profile cylinder of the same stroke.
Plan the duty around real numbers, not the rating. The fixed TPU bumper at each end absorbs end-of-stroke shock, speed spans 30-500 mm/s, and the operating envelope is 0.15-1.0 MPa (22-145 psi) with -20 to +70 C media. Note that no magnet is fitted on this version; the optional -S code adds one so CMSE / DMSE switches can sense position.
| Model | Airtac ACEJ12 Adjustable Compact Cylinder ACEJ20X80-20B |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø20 mm |
| Stroke | 80 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 118 N |
| 0.7 MPa | 165 N |
| Max (@1.0 MPa) | 24 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 20 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -20 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
The 60-80 mm trim range lets one cylinder serve pallets of different heights; about 94 N of working push at 0.5 MPa secures light aluminium parts without crushing.
At 30-500 mm/s the rod kicks off-spec cartons from a conveyor, and the short ISO 21287 body slots under low guarding where a full-length profile cylinder will not fit.
The 80 mm stroke is well inside the 100 mm maximum standard stroke for this bore. Choose the B male rod thread when your tooling screws onto the rod; the blank version offers a female M6x1.0 socket instead. Mount with FA flange or LB foot brackets, and if position feedback matters, order the -S variant so CMSE / DMSE switches can ride the body. Remember the stop screw is a mechanical end stop only - on air loss the piston drifts, so it is not a load-holding lock.
Quick checklist
The -20 code means an external stop screw shortens the 80 mm extend stroke by up to 20 mm, so the working range is 60-80 mm. It runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, temperature -20 to +70 C, with a 10 mm rod and 1/8" ports.
The ISO 21287 short body is hard-anodized aluminium with a hard-chrome-plated S45C rod, saving about 50% of the mounting length of an ISO 15552 profile cylinder. A fixed TPU bumper at both ends absorbs end-of-stroke impact. FA flange, LB foot and FTC brackets plus I/Y rod knuckles bolt to the standard face. This model has no magnet, so no switch can be fitted; order the -S code to enable CMSE / DMSE reed or solid-state switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.