
The AirTAC ACEJ12 Adjustable Compact Cylinder ACEJ20X90-10B is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø20mm bore and 90mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
A double acting ISO 21287 compact cylinder, the ACEJ20X90-10B pairs a 20 mm bore with a 90 mm stroke and a male-threaded 10 mm rod (the B code). At 0.5 MPa it pushes 157.1 N and pulls 117.8 N, rising to 219.9 N at 0.7 MPa, with a theoretical ceiling of 32 kgf at 1.0 MPa. The -10 suffix is a 10 mm adjustment window: an external stop screw trims the extend stroke anywhere in an 80-90 mm range, so one cylinder serves several fixture positions without re-plumbing.
The short hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which matters in slim gantries and guarded cells. A fixed TPU bumper at each end absorbs end-of-stroke shock, and the S45C hard-chrome rod resists wear. Note that this unit has no magnet fitted; order the -S code if you later need CMSE or DMSE switch sensing. Speed range is 30-500 mm/s.
| Model | Airtac ACEJ12 Adjustable Compact Cylinder ACEJ20X90-10B |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø20 mm |
| Stroke | 90 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 118 N |
| 0.7 MPa | 165 N |
| Max (@1.0 MPa) | 24 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 20 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
The 80-90 mm adjustable extend stroke lets a fixture designer trim the push-off position of connectors or terminals without changing the cylinder, using about 94 N of usable force at 0.5 MPa.
Size against neighbours: the 16 mm bore pushes 100.5 N at 0.5 MPa, while the 25 mm bore reaches 245.4 N, so pick the 20 mm when your load sits between roughly 90 and 150 N. The stop screw is a mechanical end stop for the extend stroke, not a mid-stroke lock, so the rod can drift if air is lost and a separate holding method is needed for suspended loads. FA flange, LB foot and FTC brackets plus I and Y rod knuckles bolt straight to the ISO 21287 face; the male rod thread suits clevis-style knuckles. PT ports, 1/8".
Quick checklist
At 0.5 MPa it pushes 157.1 N and pulls 117.8 N; at 0.7 MPa push is 219.9 N, and the theoretical maximum is 32 kgf at 1.0 MPa. It is double acting with a 90 mm stroke adjustable down to 80 mm via the -10 stop screw, running on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, temperature -20 to +70 C, with a 1/8" PT port and a male-threaded 10 mm rod.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and FA flange, LB foot and FTC brackets bolt straight to its face. Sensing requires the optional -S magnet code, which enables CMSE or DMSE switches; this model has no magnet fitted, so no switch can be read until a -S unit is ordered. A fixed TPU bumper at each end absorbs end-of-stroke impact.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.