
The AirTAC ACEJ125 Adjustable Compact Cylinder ACEJ125X250-100B is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø125mm bore and 250mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
The ACEJ125X250-100B is a double acting ISO 21287 compact cylinder with a 125 mm bore and a 250 mm stroke that an external stop screw trims on site by up to 100 mm, giving a usable extend range of 150-250 mm. At 0.5 MPa it pushes with 6135.9 N and pulls with 5890.5 N, rising to 8590.3 N on the extend side at 0.7 MPa. The male rod thread (B code) bolts straight to tooling, and the 1/4" port feeds the high air volume this bore needs.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so a 250 mm stroke fits presses and gantries that cannot accept a full-length body. A fixed TPU bumper at each end absorbs end-of-stroke energy, the hard-anodized aluminium body runs on an S45C hard-chrome rod, and speed spans 30-500 mm/s at 0.15-1.0 MPa (22-145 psi). No magnet is fitted on this version; the optional -S code adds one for CMSE / DMSE switches.
| Model | Airtac ACEJ125 Adjustable Compact Cylinder ACEJ125X250-100B |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø125 mm |
| Stroke | 250 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/4" |
| Rod thread | M16×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 5890 N |
| 0.7 MPa | 8247 N |
| Max (@1.0 MPa) | 1201 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 125 | Bore size in mm. |
| ×250 | Stroke length in mm. |
| -100 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Delivers 6135.9 N at 0.5 MPa for staking or swaging aluminium housings, with the stop screw set to 180 mm where the die travel is shorter than the full 250 mm stroke.
Pushes heavy sand-mould gates through a 150-250 mm adjustable range at 30-500 mm/s, with the male rod thread picking up the gate arm through a clevis-style knuckle.
At this bore size the choice is between trimming excess force or trimming cost. If 6135.9 N is far more than the job needs, drop to the 100 mm bore and save air consumption. The 250 mm stroke sits inside the 300 mm maximum standard stroke for this bore, so no made-to-order build is required. FA flange or LB foot mounting bolts to the ISO 21287 face, and the male rod thread suits fixtures that clamp from outside the rod end. Remember the stop screw is a mechanical end stop for the extend stroke only: on air loss the piston still drifts, so add a separate holding valve if the load must stay put.
Quick checklist
The -100 code is a 100 mm adjustment window: an external stop screw shortens the 250 mm extend stroke on site, so the usable range is 150-250 mm. It shortens the stroke only and acts as a mechanical end stop, not a mid-stroke lock.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which matters at a 250 mm stroke. A fixed TPU bumper at each end absorbs end-of-stroke energy. This version has no magnet, so no switch can be read from it; if you need end-position sensing, order the -S variant and fit CMSE or DMSE switches to the magnet slots. FA flange and LB foot mounting bolt to the standard ISO 21287 face.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.