
The AirTAC ACEJ125 Adjustable Compact Cylinder ACEJ125X75-40B is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø125mm bore and 75mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
The ACEJ125X75-40B is a double acting, adjustable-stroke compact cylinder built to ISO 21287. The -40 code gives a 40 mm adjustment window: an external stop screw trims the extend stroke anywhere between 35 and 75 mm, so one cylinder serves several die or fixture positions without swapping hardware.
The hard-anodized aluminium body with a 25 mm S45C hard-chrome rod saves about 50% of the mounting length of an ISO 15552 profile cylinder, which matters when a 75 mm stroke must fit inside a heavy press bridge or welding gantry. Male rod thread (B code), PT ports, fixed TPU bumpers at both ends, and FA/LB mounting on the ISO 21287 face. The optional -S magnet enables CMSE / DMSE switches; this model ships without a magnet.
| Model | Airtac ACEJ125 Adjustable Compact Cylinder ACEJ125X75-40B |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø125 mm |
| Stroke | 75 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/4" |
| Rod thread | M16×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 5890 N |
| 0.7 MPa | 8247 N |
| Max (@1.0 MPa) | 1201 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 125 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -40 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
The short ISO 21287 body fits inside weld gantry frames where a full-length profile cylinder will not, with LB foot mounting on standard fixture plates.
At this force class the 125 mm bore is near the top of the ACEJ range: it pushes 6135.9 N at 0.5 MPa where a 100 mm bore manages 3927.0 N, so step down only if your load stays under about 2350 N of usable force. If you need more than 75 mm of travel, the same bore takes standard strokes up to 300 mm. Remember the stop screw is a mechanical end stop for the extend stroke, not a mid-stroke lock - on air loss the piston still drifts, so add a separate holding valve for suspended loads. Order FA flange or LB foot to suit the fixture, and add the -S code if CMSE / DMSE position sensing is planned.
Quick checklist
It is double acting with a 75 mm stroke adjustable down to 35 mm via the -40 stop screw, running on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, temperature -20 to +70 C, with a 1/4" PT port and a 25 mm male-thread rod.
It is an ISO 21287 compact cylinder: hard-anodized aluminium body, threaded aluminium covers, and a hard-chrome plated S45C rod, saving about 50% of the mounting length of an ISO 15552 profile cylinder. Fixed TPU bumpers at both ends absorb end-of-stroke energy. FA flange and LB foot mount on the standard ISO 21287 face. Position sensing needs the optional -S magnet code - this model has no magnet, so CMSE / DMSE switches cannot be fitted unless you order -S.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.