
The AirTAC ACEJ32~40 Adjustable Cushion Compact Cylinder ACEJ32X150-10B is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø32mm bore and 150mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
The ACEJ32X150-10B is a double acting AirTAC compact cylinder built to ISO 21287, with a 32 mm bore and a 150 mm stroke that an external stop screw can trim by up to 10 mm on site, giving a usable extend range of 140-150 mm. At 0.5 MPa it pushes with 402.1 N and pulls with 345.6 N, rising to 563 N on the extend stroke at 0.7 MPa. The hard-anodized aluminium body with an S45C hard-chrome plated 12 mm rod runs at 0.15-1.0 MPa (22-145 psi) and 30-500 mm/s.
Because the short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, it slots into tight jigs and guarding where a full-length body will not fit. As a working figure, plan for roughly 240 N (about 24 kg) of real push work at 0.5 MPa, which is a sensible 0.6 margin below the 402.1 N rating. The male (B code) rod thread suits tooling plates that take a threaded stud. Note this unit has no -S code, so no magnet is fitted and CMSE / DMSE switches cannot be used unless you order the optional -S magnet version.
| Model | Airtac ACEJ32~40 Adjustable Cushion Compact Cylinder ACEJ32X150-10B |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø32 mm |
| Stroke | 150 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 32 | Bore size in mm. |
| ×150 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
A 150 mm stroke sweeps cartons off a conveyor into a lane, with the stop screw trimming the throw to match lane width without changing cylinders.
The male rod thread bolts straight to an ejector plate, and the 24 kg usable push at 0.5 MPa clears finished parts from a nest at up to 500 mm/s.
The stop screw is a mechanical end stop for the extend stroke only - it does not lock or hold a load if air is lost, so add a separate valve or clamp for holding. Mount it on the ISO 21287 face with FA flange or LB foot brackets, and I or Y rod knuckles thread onto the male rod end. If you later need position sensing, order the -S variant with the optional magnet for CMSE / DMSE switches.
Quick checklist
At 0.5 MPa it pushes 402.1 N and pulls 345.6 N; at 0.7 MPa push is 563 N and pull 483.8 N, with a theoretical maximum of 82 kgf at 1.0 MPa. It is double acting, runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), temperature -20 to +70 C, speed 30-500 mm/s, with a fixed TPU bumper at both ends and a 1/8" PT port.
An external stop screw shortens the 150 mm extend stroke by up to 10 mm, so the working range is 140-150 mm; it is a mechanical end stop, not a mid-stroke lock, and the rod still drifts if air is lost. The body is a compact ISO 21287 design about 50% shorter in mounting length than an ISO 15552 profile cylinder, taking FA flange or LB foot brackets. This unit has no magnet, so CMSE / DMSE switches need the optional -S magnet code.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.