
The AirTAC ACEJ32~40 Adjustable Cushion Compact Cylinder ACEJ32X175-40B is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø32mm bore and 175mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
The ACEJ32X175-40B is a double acting AirTAC compact cylinder built to ISO 21287, with a 32 mm bore and a 175 mm stroke that an external stop screw trims by up to 40 mm on site, giving a usable extend range of 135-175 mm. At 0.5 MPa it delivers 402.1 N forward and 345.6 N on retract, rising to 563 N at 0.7 MPa. Its hard-anodized aluminium body takes roughly 50% less mounting length than an ISO 15552 profile cylinder, so it slots into tight gantries and guarding where a full-length body cannot.
The S45C hard-chrome-plated 12 mm rod ends in a MALE thread (the B code), the air port is 1/8", and a fixed TPU bumper at each end absorbs end-of-stroke shock. Speed range is 30-500 mm/s over 0.15-1.0 MPa (22-145 psi). Note that no magnet is fitted on this version; the optional -S code is required before CMSE or DMSE switches can be used.
| Model | Airtac ACEJ32~40 Adjustable Cushion Compact Cylinder ACEJ32X175-40B |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø32 mm |
| Stroke | 175 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 32 | Bore size in mm. |
| ×175 | Stroke length in mm. |
| -40 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
With about 241 N of practical working force, the 175 mm stroke diverts cartons between lanes, while the compact body fits under low guard rails.
The 563 N available at 0.7 MPa seats bearings, bushings and dowel pins in light assembly work, with the male rod thread simplifying tooling attachment.
The 175 mm stroke sits inside the 200 mm standard range for bore 32, so no made-to-order stroke is needed. The stop screw shortens the extend stroke only - it is a mechanical end stop, not a mid-stroke lock, so the piston will still drift if air is lost. Choose FA flange or LB foot mounting to suit the fixture, and add the -S code if position sensing with CMSE / DMSE switches will be needed later.
Quick checklist
Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the extend stroke is adjustable from 135 to 175 mm via the 40 mm stop-screw window.
An external stop screw shortens the 175 mm extend stroke by up to 40 mm, so the working range is 135-175 mm; it cannot lengthen the stroke beyond 175 mm. The stop is a mechanical end stop only and does not hold a load if air pressure drops. This unit has no magnet, so CMSE or DMSE switches require ordering the optional -S magnet version. Mounting options include FA flange and LB foot, and the short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.