
The AirTAC ACEJ50~63 Adjustable Compact Air Cylinder ACEJ63X100-100B is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø63mm bore and 100mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
A double acting ISO 21287 compact cylinder with an adjustable extend stroke, the ACEJ63X100-100B pairs a 63 mm bore with a 100 mm stroke that an external stop screw can trim anywhere in a 100 mm window, giving a usable range of 0-100 mm on the machine. At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N, rising to 2182.1 N on the extend stroke at 0.7 MPa, with a theoretical ceiling of 317.9 kgf at 1.0 MPa. The male (B code) rod thread suits fixtures that clamp on the rod itself.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight press frames and guarding where a full-length body cannot. A hard-anodized aluminium barrel carries the 16 mm hard-chrome S45C rod, and fixed TPU bumpers absorb end-of-stroke energy at both ends. Running spec: 0.15-1.0 MPa (22-145 psi), 30-500 mm/s, air filtered to 40 um. Note that no magnet is fitted on this version; order the -S code if CMSE / DMSE switch sensing is needed later.
| Model | Airtac ACEJ50~63 Adjustable Compact Air Cylinder ACEJ63X100-100B |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 100 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 250 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 63 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -100 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Male-threaded rod drives ejector pins on machined-part fixtures, with the 0-100 mm adjustable range matching varying part heights.
The stop screw is a mechanical end stop for the extend stroke, not a mid-stroke lock, so the piston still drifts if air is lost - do not use it to hold a load. FA flange, LB foot and FTC brackets plus I/Y rod knuckles bolt to the ISO 21287 face, and the optional -S magnet enables CMSE / DMSE switches.
Quick checklist
At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N; at 0.7 MPa push is 2182.1 N and pull 2041.3 N; theoretical maximum is 317.9 kgf at 1.0 MPa. The -100 code sets a 100 mm adjustment window: an external stop screw shortens the 100 mm extend stroke by up to 100 mm, so the working range is 0-100 mm. It is double acting, runs 30-500 mm/s on 0.15-1.0 MPa (22-145 psi) air, and the port is 1/8" (PT).
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with fixed TPU bumpers at both ends and FA/LB/FTC mounting plus I/Y rod knuckles. This model has no magnet fitted; the optional -S code adds one so CMSE / DMSE reed or solid-state switches can be mounted on the body slots.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models are processed and dispatched in 3-5 business days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.