Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ80X110-50
The AirTAC ACEJ80~100 Adjustable Compact Cylinder ACEJ80X110-50 is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø80mm bore and 110mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ80 mm
- Stroke110 mm
- Port size1/8"
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ80X110-50
An external stop screw trims the extend stroke anywhere in the ordered 50 mm window, giving a usable range of 60-110 mm without changing hardware. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into presses and gantries where a full-length body will not fit.
The hard-anodized aluminium body carries a S45C hard-chrome plated 20 mm rod, a fixed TPU bumper at each end absorbs end-of-stroke energy, and the optional -S magnet enables CMSE / DMSE switch position feedback. Ports are 1/8" and the rod end is female M12x1.75.
Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ80X110-50 Technical Specifications
| Model | Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ80X110-50 |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 110 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ80X110-50
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 80 | Bore size in mm. |
| ×110 | Stroke length in mm. |
| -50 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ80X110-50 Is Used
Pallet gate and stopper actuation
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits under conveyor lines as a pop-up stopper or gate driver with 2356.2 N of pull force on retract.
Is the Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ80X110-50 the Right Cylinder?
If your load needs under 1558.6 N, a 63 mm bore does the job in a smaller envelope; if you need beyond 3518.6 N at 0.7 MPa, step up to 100 mm bore (3927.0 N at 0.5 MPa). Size on the pull figure too when the rod retracts under load.
The stop screw is a mechanical end stop for the extend stroke only - it does not lock the piston mid-stroke, and on air loss the rod can drift, so add a separate holding valve where a load must stay put. FA flange, LB foot and I/Y rod knuckles bolt to the ISO 21287 face; order the -S code if you need CMSE / DMSE sensing, since without it no magnet is fitted.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ80X110-50 FAQ
At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N; at 0.7 MPa those rise to 3518.6 N and 3298.7 N, with a theoretical maximum of 512.6 kgf at 1.0 MPa. The -50 code is a 50 mm adjustment window: an external stop screw shortens the 110 mm extend stroke on site, so the working range is 60-110 mm. It shortens the stroke only - it never extends past 110 mm and it is not a mid-stroke lock, so the rod can drift if air is lost. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the port is 1/8" with a female M12x1.75 rod thread.
It is built to ISO 21287 as a compact cylinder: a hard-anodized aluminium body with a roller-burnished bore, threaded aluminium covers and a S45C hard-chrome plated 20 mm rod, saving about 50% of the mounting length of an ISO 15552 profile cylinder. A fixed TPU bumper at each end absorbs end-of-stroke energy. Position sensing requires the optional -S magnet code - this model has no magnet fitted, so no switch can be read until you order -S, after which CMSE or DMSE switches mount in the body slots. FA flange, LB foot and I/Y rod knuckles attach to the standard ISO 21287 mounting face.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ80X110-50
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.