Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ80X80-20SB
The AirTAC ACEJ80~100 Adjustable Compact Cylinder ACEJ80X80-20SB is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø80mm bore and 80mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ80 mm
- Stroke80 mm
- Port size1/8"
- Acting typeDouble acting, double rod, adjustable stroke
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ80X80-20SB
A double acting ISO 21287 compact cylinder with an adjustable extend stroke, the ACEJ80X80-20SB pairs an 80 mm bore with an 80 mm stroke and a 20 mm trim window: an external stop screw shortens the extend stroke anywhere between 60 and 80 mm, so one unit serves several fixture positions. At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N, rising to 3518.6 N on extension at 0.7 MPa, with a theoretical ceiling of 512.6 kgf at 1.0 MPa.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into presses, weld fixtures and gantries where a full-length body cannot. The hard-anodized aluminium body carries a hard-chromed S45C 20 mm rod, fixed TPU bumpers absorb end-of-stroke energy at both ends, and because this model carries the -S magnet, CMSE or DMSE reed and solid-state switches can be fitted for end-position sensing. The B code gives a male rod thread; ports are 1/8".
Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ80X80-20SB Technical Specifications
| Model | Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ80X80-20SB |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 80 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
Model Code: Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ80X80-20SB
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 80 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -20 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ80X80-20SB Is Used
Weld fixture clamping
The compact body fits inside weld-cell tooling where an ISO 15552 profile cylinder is too long, and the -S magnet plus CMSE switch confirms clamp-seated position for the PLC.
Pallet gate actuation
Pulling 2356.2 N at 0.5 MPa gives enough force to swing heavy conveyor gates and diverters in a distribution centre, with the 20 mm window trimming the swing to match the gate.
Is the Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ80X80-20SB the Right Cylinder?
Remember the stop screw is a mechanical end stop for the extend stroke, not a mid-stroke lock: on air loss the piston still drifts, so add a separate holding valve where a load must stay put. FA flange, LB foot and FTC brackets plus I and Y rod knuckles bolt to the ISO 21287 face, and the male rod thread (B) suits clevis-style tooling.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ80X80-20SB FAQ
At 0.5 MPa it pushes 2513.3 N and pulls 2356.2 N; at 0.7 MPa those figures rise to 3518.6 N and 3298.7 N, with a theoretical maximum of 512.6 kgf at 1.0 MPa. The -20 code sets a 20 mm adjustment window: an external stop screw trims the 80 mm extend stroke down to as little as 60 mm, so the usable range is 60-80 mm. It shortens the stroke only and never extends it past the ordered length.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which frees space in guarded machines and tight jigs. This model carries the optional -S magnet, so CMSE or DMSE reed and solid-state switches can be mounted in the body slots for position feedback. FA flange, LB foot and FTC brackets plus I and Y rod knuckles attach to the standard ISO 21287 face, and the male rod thread (B code) accepts threaded tooling directly.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACEJ80~100 Adjustable Compact Cylinder ACEJ80X80-20SB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.