This model is discontinued
AirTAC has phased out the ACP series. You can still order this code here: we ship the current replacement ACED25X10, the same code under the new prefix. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD25X10
The AirTAC ACPD Double Rod Compact Cylinder ACPD25X10 is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø25mm bore and 10mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED25X10 (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ25 mm
- Stroke10 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod
- Rod threadM6×1.0
- StatusDiscontinued → ACED25X10
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD25X10
This is a double acting compact cylinder with a through rod: a 10 mm piston rod exits BOTH covers of the ACPD25X10, so the 25 mm bore delivers the same 206.2 N in each direction at 0.5 MPa (288.6 N at 0.7 MPa), because both strokes work on the rod-side area. The short ISO 21287-class body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it slots into tight jigs and slide assemblies a full-length body cannot. Note that this model is discontinued; the current-production direct is the ACED25X10 (swap the P for an E), so confirm ISO 21287 mounting dimensions before ordering.
The back-end rod doubles as a sensor-flag carrier or a symmetric second mount, and the through rod resists rotation and side load better than a stub single rod. Ports are M5x0.8, the female rod thread is M6x1.0, speed runs 30-500 mm/s, and a fixed TPU bumper pads both ends. The optional -S magnet code enables CMSE / DMSE switches; without it there is no magnet fitted.
Airtac ACPD Double Rod Compact Cylinder ACPD25X10 Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD25X10 |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED25X10 |
| Bore size | Ø25 mm |
| Stroke | 10 mm |
| Acting type | Double acting, double rod |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 150 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED25X10 (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD25X10
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 25 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (double rod, adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD25X10 Is Used
Fixture clamping in tight dies
The 10 mm stroke and short body let the ACPD25X10 clamp small stamped brackets inside a press die, pushing 206.2 N both ways at 0.5 MPa so the clamp and release forces match.
Symmetric slide drive with position feedback
A pick-and-place slide on a small assembly cell uses the through rod for a rotation-resistant guide, and with the optional -S magnet a DMSE switch confirms each 10 mm end position.
Push-pull gate indexing
A bottling-line lane gate needs equal force in both directions; the double rod gives 288.6 N at 0.7 MPa either way, so the gate indexes at the same speed returning.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD25X10 with the ACED25X10
At 25 mm bore the ACPD25X10 gives 206.2 N both ways at 0.5 MPa. If your load needs less, the 20 mm bore offers 117.8 N; if you need more, step up to the 32 mm bore at 345.6 N. The 10 mm stroke suits short indexing and part-present moves. Remember that a plain double-rod cylinder drifts when air is lost, so add a rod lock or pilot check for a held load. FA/FB flange or LB foot mounting bolts to the standard face, and the optional -S magnet lets CMSE / DMSE switches report end positions. This model is discontinued - order the ACED25X10 as the current direct and verify the ISO 21287 mounting dimensions.
Replacement checklist
- ✓ Current-production ACE → ACED25X10
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD25X10 FAQ
Because a rod exits both covers, force is equal both ways: 206.2 N at 0.5 MPa and 288.6 N at 0.7 MPa, on every stroke of the 25 mm bore. Peak force at 1.0 MPa is 42.0 kgf. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof 1.5 MPa (215 psi), speed 30-500 mm/s, port M5x0.8, female rod thread M6x1.0.
The hard-anodized aluminium body follows the short DIN-standard compact format, saving about 50% of the mounting length of an ISO 15552 profile cylinder, with a fixed TPU bumper at each end. The ACPD25X10 is discontinued; the current-production replacement is the ACED25X10 in the same bore, stroke and force class - confirm the ISO 21287 mounting dimensions before swapping.
Request a Quote for the ACED25X10
Send us the quantity and destination. We confirm price, stock and lead time on the ACED25X10 replacement — usually within 7-8 hours.